Question about Hotpoint Aquarius WD63 Front Load Washer/Dryer

1 Answer

Rattle on fast spin

Our washinf machine (aquarius WM63) rattles as though something metal in drum. However I can't see anything when it has no washing in it so I assume its between the drums. Any suggestions?
Cheers

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 57 Answers

Hi mate the rattle could be caused by a coin are a bra wire regards a coin you would have to take off the main pump hose connected to the drum our else take the heater element out and see if you can find it if it is a bra wire just rotate the drum until you see it and pull it out

Posted on Jul 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rattling drum spin


sounds like the spider and drum bearing are on there way out

Sep 30, 2012 | Hotpoint Aquarius WF220 Front Load Washer

1 Answer

Hot point WF451 Issue. I want change the door rubber between the door and drum. How do I do this? Also the machine is making a noise on fast spin as if there is something in the drum catching. I have...


Hi for changing the door seal check out the video section on www.selfix-uk.co.uk there are a few videos on the wf including bearing change which also covers the door seal as well. As far as the noise in your machine it could be almost any thing...if it's a scrapping noise it may be a bra wire caught between the drum and container, if its a tapping noise it may just be loose wires hitting on the cabinet or you may have a coin between the drum and container if it's a loud rattle, you could also have something in the pump housing...it's hard to diagnose noises without actually hearing them sorry

Jan 23, 2011 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

My Aquarius WF541 drum won't turn when I switch it on, although the motor seems to be?? I've cleaned the filter, and got 2 coins and what looked like metal filings, but they may have been plastice, seems...


Try turning the drum by hand from the front of the washer, if it feels rough o ris grinding or rumbling, then the main drum bearings have probably failed, also try lifting the drum up and down from the front, see if there is any movement of drum, if there is, then again it is a main bearing problem.
If all o/k, then remove the lower rear cover, and check the belt is o/k.

Nov 29, 2010 | Hotpoint Washing Machines

1 Answer

Hotpoint Aquarius 1100 WM63 Not Spinning Clicking Programmer


I would suggest you check the brushes in the motor, as it sounds like they are worn out.
Replace them if they are less than 3 or 4 mm long
This would give you the symptoms you are describing.
Please rate my solution.
Thankyou.

Feb 09, 2010 | Hotpoint Aquarius WF000 Front Load Washer

1 Answer

When in fast spin there is a loud rattling sound as though there are stones in the drum


You could have something fast between the inner and outer drum, or one or more of the drum paddles is loose..
Remove lower rear panel of washer, remove the belt, and from the front spin the drum by hand, this this will show if the drum bearings are o/k.
There should be little or no noise from the drum.
If it is rumbling, or feels rough, then the main bearings have failed.
If ther is something caught, then you will hear it catching or clicking.
Hope this helps.

Dec 10, 2009 | Hotpoint Aquarius WMA56 Front Load Washer

1 Answer

Aquarius 1100 wm63 very noisy spinning


Remove rear cover of washer.
Remove drive belt.
From inside the drum, spin the drum by hand, if it is noisy or feels rough, then main drum bearings have failed.
If no noise, then possibly motor bearings noisy.
Hope this helps Thankyou.

Nov 27, 2009 | Hotpoint Washing Machines

1 Answer

Hotpoint Aquarius 1100 WM63. fills with water...I dont think it is heating water...rarely rotates and spins (saw it once in early stage of J prog only) seems to fill and empty but no rotate or spin....


if it fill with water then stops it is the ellement the machine first fills turns the drum then heats up the thermostat cuts in and the it emptys rinses and spins so if it does not get to temp it will stop or continue to wash forever

Jun 27, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Washing machine makes a loud rattling sound


Hi.k.
Even though you have cleaned filter, there could still be something in the pump, you need to remove the pump and check there is nothing in it.
Hope this helps.
Good luck.
Please leave feedback

Nov 30, 2008 | Kenmore 98702 Stacked Washer/Dryer

1 Answer

Beko


probably a balancing spring broken the load will go to one side of the drum when spinning.Needs to be taken care of before it rattles itself to death

Oct 21, 2007 | Hotpoint Aquarius WMA56 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WD63 Front Load Washer/Dryer Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...