Question about Gateway FPD2275W LCD Monitor

1 Answer

I cannot open this websites in my collage library.

You tube, orkut

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,043 Answers

Do you get a message like "this site blocked?"
It is very possible that the library blocked access to those sites with firewall rules.

Posted on Jul 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Black out


In most cases, the problem is caused by faulty filter capacitors in the power supply. You can open the back and replace the capacitors that look bulged and leaky or replace all the electrolytics in the power supply board. If it continues to turn off like that, the tubes are at the end of their service life.

If you have no desire to buy a new monitor at that point, the tubes are able to be replaced, but for overall simplicity- just order the replacements aet up for your specific monitor from Dell. Make sure they have the boots, the plastic attachments and connector for "drop in" use. If the tubes require connectors to be soldered on, it gets tedious and is not worth it from a standpoint of shop time..

Feb 12, 2012 | Dell E176FPB 17" TFT LCD Flat Panel...

2 Answers

The monitor goes black and then comes back on if you turn it off and back on. E228WFPc monitor by dell Can I repair it myself?


Open the monitor and look for blown capacitors on the power PCB. Replace with the same capacity and voltage. Usually they are 1000uF/35V or 470uF/35V
The luminiscent tube(s) may be worn out, broken or disconnected; or the solders on both ends on the tube may produce electric arc to the ground.
Replacing the tubes is hard to do at home. It requires very clean place because the LCD have to be disassembled and it's very likely to get dirty, leading to image defects.

Aug 01, 2010 | Dell E228WFP LCD Monitor

1 Answer

How do i remove run.dll2 from my computer?


Hi,

Rundll.exe files are programs that are directly tied to the registry on Windows computers. Dynamic Link Library (DLL) files contain libraries of information used by other programs running on your computer. They were originally created in order to help computer programs run faster on the Windows operating system. When a DLL file is corrupt or missing, a Rundll error will be generated. Normally when a rundll error is generated it is related to malware.

  1. Note the process that is generating the Rundll error by examining the last file name in the error that ends in ".dll."
  2. Open the service configuration program on your computer by selecting the "Start" menu and typing "command" in the search text field. At the DOS prompt type "services:msc" and click "Enter."
  3. Select the DLL service from Step 1. Right click the service name followed by the "Stop" menu button. Exit the service configuration program.
  4. Open your computer's registry editor by typing "regedit" at the DOS prompt and navigate to the Rundll registry key by typing "Microsoft\Windows\CurrentVersion\Run" in the Search field.
  5. Select the registry key returned and in the value associated with the registry key, confirm it ends in the same DLL file name found in Step 1. If it does, single left click the value and Press the "Delete" key. Exit the registry editor.
  6. Restart your computer and the Rundll error will be corrected.

Good luck!
Save a tree.

Apr 28, 2010 | HP W19b LCD Monitor

1 Answer

How to disassemble


There is ccfl(cold cathode fluroscent lamp) tube which is faulty therefore no light is there the ccfl tube operates on 600vac with 40khz-60khz so check 600vac to the tube if no voltage is there then check circuit and to open see any locks available there if no screw is observed take a smallest screwdriver (preset alligner)to open the lock

Mar 13, 2010 | ViewSonic VA721 17" LCD Monitor

2 Answers

My monitor has no red color. modle#DL36,serial#011378,MFG.1,1999. can this be repaird? if so where? gateway brand.


Before you replace it (don't repair it) with an LCD monitor:

1.Push and tighten the monitor cable where it connects to the computer.
2. Push and tighten the monitor cable behind the monitor if it has a connector.

3. If these fail, then (seriously) whack the monitor on either side with your open palm.

4 Repeat #4 a couple of times, maybe on the left side this time.

5. Tube/gun/circuit is failing, replace monitor ($80 ~ $120).

Hope this at least temporarily helps...

Sep 10, 2009 | Computer Monitors

1 Answer

Spackling Noise when Switched on!


not capacitor the rotten smell and fire, but fly back monitor you, if it is opened you will see large black color paste that into the tube, please remove and pull it out and clean the contacts of the tube, but careful You strongly its electricity, using a wire that is long and 1ft jab to cap that the flame tube and jab you in the ground one end and then you lift partially.good luck and careful

Jul 20, 2009 | Dell E773C 17" CRT Monitor

1 Answer

Color problem


Hi, it is more likely from an open green and/or blue picture tube's electron gun transistor driver.
If you have an experience on electronics / or use of solder gun, you can just open your monitor and look for the electronic board at the back of the picture tube. Take a look in all transistor ( components with three legs) and solder / check if their legs are not fully soldered to the board. Note: just be careful on the high voltage diode / line ( the one with a thick (like the car distribution wire cable) single wire going to the tube). good luck

Dec 19, 2008 | IBM E74 17" CRT Monitor

1 Answer

Dell E152 Flat Panel screen is REALLY dim.


I haven't seen this particular monitor. It may have deeply recessed black screws, or possibly even Torx screws. Try a #2 Phillips and see if it engages firmly. If not, try a T-10. Once you get inside, you will need to remove the power supply and main board to get at the LCD panel. Locate the inverter circuit - it will have two Teflon insulated wires going to (usually) the bottom corners of the panel. It may be part of the power supply board. Every LCD display I've seen so far uses pink colored insulation on those wires. It is possible that the inverter has failed, but most of the time, it's the fluorescent tubes inside the back of the panel.

Getting at the tubes without breaking something is not a trivial task. You will most likely need a #00 Phillips screw to remove the shield metal. Observe anti-static precautions from the moment you open the monitor. Be patient, and keep track of every part or connection you remove. Do not remove the LCD driver circuitry (generally at the top) from the panel. The tube(s) are usually at bottom, enclosed in a sheet metal reflector held in place by the bottom section of the thin metal frame around the panel, just inside a flexible white plastic sheet that covers most of the back of the panel.

You can get new backlight fluorescent tubes from www.lcdparts.com. This website has links to some very helpful pages on repairing LCDs. Note: replacing the tubes involves some rather delicate work. If you are nervous, twitchy or clumsy with fine work, you'd be better off to hire out the job. Be very careful not to rip the rubber insulators on the ends of the tubes when you slide them down the insulated wires to expose the connections to the tubes. You have to attach the wires at just the right spot or you won't be able to fit the insulators back on and get the new tubes to go into the LCD frame - and you can't apply heat to the wires for more than 4 seconds at a time. I've done a number of them successfully, but have occasionally had to try several times to make the connection sufficiently small and short.

Dec 18, 2008 | Dell E172FP 17" LCD Flat Panel Monitor

2 Answers

Hp vs17e monitor manual dowmload


For Jimmy- HP's website is a nightmare but I'm sure the user guide can be had there; it will just take time to locate it.

For Rosignoli- you won't get much help without telling us what kind of computer (Apple - Wintel) the model, operating sytem, etc.
This isn't the psychic hotline.

If you need a general course in computer use, many local schools and libraries offer beginner's courses, mostly at very low cost or free of charge.

Aug 24, 2008 | Computer Monitors

Not finding what you are looking for?
Gateway FPD2275W LCD Monitor Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Gateway Computer Monitors Experts

olayoju victor

Level 2 Expert

191 Answers

NIK
NIK

Level 2 Expert

206 Answers

David Payne
David Payne

Level 3 Expert

13437 Answers

Are you a Gateway Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...