Question about 3Com 4500 24-Port Ethernet Switch

2 Answers

I cann't connect to my switch

Hi mr

i want connect to my switch 3com super stack 3 - 26 port for do configer

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

Your superstack 3 should have a 9 pin male connector at the back labeled "console port" you need to connect this to your serial interface on your pc or laptop. With 3Com you also need to set your baud rate to 19200 as this the default for 3Com.

Posted on Oct 19, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

The primary connection method for those switches would be serial connection. In the box there should have been a DB9 serial to RJ45 cable. Hyperterminal default settings would allow you to connect.

Posted on Dec 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

3com don't telnet


Make sure its not blocked from the router settings and the corresponding port is open.

Sep 24, 2013 | 3Com Computers & Internet

1 Answer

What is the defult ip address for access the config page at switchs 3com?


The default IP address of the device, depends on the status of the network where the device resides, but if the device is not connected to the network, or no DHCP server exists in the subnet where the device resides, you can get the default IP address of the device on the label on the right of the device rear panel.

Feb 24, 2011 | 3Com Baseline Plus 2952 52 Port Gigabit...

1 Answer

Sir I have 4200 series 26 ports Switch i want to Configure intra VLAN But I am Getting a problem to Configure that switch . After Cnfigure VLAN on Consol prompt. I am not accessing to my Server & WAN...


Hi,
If you are creating only Layer 2 VLANs on the switch , you wont be able to ping the servers and Routers as they are in default VLAN1.
you can do the below steps
1. Create sub interfaces on the router LAN interface
2. Provide a new ip range to the new sub interface
3. Make the switch port connecting router as trunk, so that it will carry both the VLAN info
4. on your Labtop/PC give the IP address in the newly defined range
5. Make your switch port to be in the new VLAN

This will work , if you wont be able to configure the above settings, let me know i will give you the detailed config

Nov 01, 2010 | 3Com 4500 24-Port Ethernet Switch

1 Answer

Confi stack on nortel switch 2526


Hi friend i want help can you give me the reply. i have 4 nortel 2550T-24 port switch but i don't know how to active stack config.

Sep 27, 2010 | Nortel 2526T-PWR Ethernet Routing Switch...

1 Answer

3com nj220 central config error response from device


Found that the problem was in the installation of the service.

There were two .exe in the installation software, one labeled setup.exe and the other "3Com IJNJ Configuration Software.exe". setup.exe is what needs to be used and it will in turn call the other. I had opened the other directly.

Feb 08, 2009 | 3Com NJ220 Networking Switch

1 Answer

How can i stack 3com 4900sx switches? Do i need accessories to do this?


If you would like mulitple switchs its as simple as running a patch cable from you port in the switch to one port in the other switch.

Other user: There is no such thing as dhcp in a switch that is done by higher level networking leveling like routers

Jan 13, 2009 | 3Com (3C17206TAA-US) 24x10/100 Mbps...

2 Answers

Fiber module


Hi,

you can login though the console cable, switch back side conso;e port will be there, it will bw like RJ 45 port

May 10, 2008 | 3Com SuperStack 3 4400 (3C17204-US)...

3 Answers

3Com 3824


Download free version of HyperTerminal for Vista : ftp://ftp.hilgraeve.com/htpe/htpe63.exe
Make a new connection :
connect using COM1 (depends of your configuration)
19 200 bits/sec
8 data bits
No parity
1 stop bit
No control of flux

And push enter twice to display a "Login:" prompt.
Connect using default user/passwords : http://support.3com.com/infodeli/tools/switches/ss3/management/ug/setup.htm#13131

Regards,

AstroMan

Jan 14, 2008 | 3Com SuperStack 3 3824 (3cr17402-91-uk)...

1 Answer

Link and activity lights on 3Com Switch ports without connection


Do the ports work when the cables are connect?  I did some re-search and this seems to be an ongoing issue with 3com switches.  It should not effect the use of the switch

Oct 09, 2007 | 3Com 3C16985B /REF3COM SSII 24-PORT SWITCH...

1 Answer

Stacking Cable / SuperStack3 3870


Found this on 3Com website: The SuperStack 3 Switch 3870 family (3870-24 and 3870-48) can stack up to 8 units high. Stacks can be formed with any combination of 24-port and 48-port units, with a maximum of 384 (8 x 48) front panel ports supported. When connected together, a stack of units is managed as a single entity. All units in the stack need to run the same release of the operational version code (firmware). When units are stacked together, they operate in a master-slave relationship. One unit acts as a Master and the other units act as slaves. When looking at a stack of units, the master can be identified by looking at the Stack Master LED on the left side of the switch. The Stack Master LED is green for the Master. If the unit numbers are out of sync, go to the CLI command that allows users to re-number their units- system / control / renumber. This will re-number the units in the stack. It will take about a minute or two. The master is the only unit that has a visible command line interface (CLI) when a console cable is connected to it. If you connect the console cable to a slave unit, you will not see the CLI menu, but instead see slave status messages being displayed. The Master unit may not be unit 1. http://knowledgebase.3com.com/consumer/esupport.asp?id=GUIDbfa9caa4%5F138f%5F4681%5Fbaaf%5F5c99ec5b7ff4&resource=&number=0&isExternal=0&nShowFacts=&nShowCause=&nShowChange=&nShowAddInfo=&activepage=statement.asp&bForceMatch=True&strCurrentSymptom=3C17462&searchtype=normal&searchclass=&bnewsession=false&selecttype=match

Nov 21, 2006 | 3Com (3c17462)

Not finding what you are looking for?
3Com 4500 24-Port Ethernet Switch Logo

Related Topics:

1,017 people viewed this question

Ask a Question

Usually answered in minutes!

Top 3Com Computers & Internet Experts

NBX_Tech
NBX_Tech

Level 1 Expert

58 Answers

steve morris
steve morris

Level 3 Expert

1675 Answers

micky dee

Level 3 Expert

2642 Answers

Are you a 3Com Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...