Question about Projection Televisions

1 Answer

I bought ajumbo remote and doon't have the directions

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 163 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

RCV HDTV model HD52W66 having issue where 3 images (like the Direct tv guide or a channel) show up at once.


DVI does not carry sound
that is an out of sync pic like your running a 1080p to a 720p
Some direct TV guy needs to answer this likely
or you have a 18pin instead of 21 pin hdmi side connector that too is an issue for some.

Jan 04, 2015 | RCA Projection Televisions

1 Answer

Big sreen tv problem


Are you talking about the direct remote or the remote for the set?

The direct remote should be programable for most sets and most set remotes will program for direct boxes.

Mar 16, 2012 | Projection Televisions

1 Answer

Lost remote controller of salora TV


Universal remote might work? Salora device codes are listed on most universal TV remote manuals.

May 10, 2009 | Draper Salara Electric Front Projection...

1 Answer

I just bought this TV, but I can not get the TV


push the input button on the remote and match up your input signal with the tv

Apr 16, 2009 | Samsung HCL5515W 55" Rear Projection...

1 Answer

Remote won't work.


this would be the IR sensor on the tv that recieves the signal from the remote , but testing of the sensor and components in the circuit should be done.
there will be an Identification number on the sensor and you will have to get that ID and you can either google it or post it here and I will help you find the sensor

Mar 19, 2009 | Toshiba 50A61 50" Rear Projection...

1 Answer

Lost directions to program philips universal remote. I have a zenith tv.


All I needed was a four diget code. I dropped the eight dollar remote which caused the batteries to fall out. I just went to Wal Mart and bought a new one.

Nov 03, 2008 | Projection Televisions

1 Answer

I want to program my remote control to work with my direct t.v.


Look in the user manual for your remote.
You should find a table with brands and types of devices.
Your direct tv should be listed as such.
There will be a number code for the direct tv that you will need to program the remote with.
The manual should also tell you what buttons to press in order to program.
Otherwise, have only the direct tv receiver ON.
point your remote at it and press the tv button and then the power button on the remote and hold it down while pressing the cursor up and down buttons. (not channel up and down. The up and down are the ones to select other things on the remote with.
When you have the right code the tv will shut off.
After it has shut off stop pushing buttons and then press the power button on the remote.
Your direct tv should now be programmed to turn on and off with the remote.
Note: be sure when you turn various devices on or off, have it selected for that devices you are trying to turn on or off.

Apr 30, 2008 | Projection Televisions

1 Answer

Can i program my remote to change channels through my direct tv box


No Direct TVs need their own remotes. You can get a replacement Direct TV remote at the following link they ship for free anywhere in the U.S.
http://servicemanuals.vstore.ca/

Apr 12, 2008 | Projection Televisions

2 Answers

Need remote control code for 32" X2GEN tv


Good luck. I have the same issue. No codes are available for the X2Gen. To make matters worse, it appears to use a non-standard frequency for the carrier signal, maening that other remotes won't work with the TV.

I purchased a learning remote, thinking I would just "teach" it the codes directly from the X2Gen TV remote. This didn't work either.

There appears to be no way to use any remote other than the one supplied with the TV. Whatever you do, don't lose it!

Jan 24, 2008 | Projection Televisions

2 Answers

MITSUBISHI WT-46805 No Volume


Sounds like audio output IC is bad.Hope this helps. It is on the center circuit board on a little heat sink directly in front of the large Convergence heat sink. It is referred to as IC3E01 and the part number is LA4663. Hope this helps. Let me know if i can assist you further.

Nov 05, 2007 | Mitsubishi WT-46809 46" Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...