Question about Epson EMP 7500 Multimedia Projector

1 Answer

No pawer ther is a fuse sadnly no pawer

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have you checked if there is a fuse inside the projector

Posted on Aug 13, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

, the color looks fade. At any mode


Most likely your LCD panels are going out and there is light leak even on 'black' for specific colors. Depends on what kind of projector and model, but I'd replace it. Sounds like it has surpassed its useful life.

Feb 19, 2015 | Office Equipment & Supplies

1 Answer

Fuse


Hello!
Why do you want to replace fuse? Is your projector dead? In many cases just a fuse replacement will not solve the problem. if fuse is blown, good chance, that power supply has shorted components. still, you may try to replace the fuse with lower grade, first, and observe the behavior. If unit turns on and starts operate normally, then fuse blows, you may install the stock fuse. Means: it's just a fuse's issue. If it blows right away, don't even try to put regular fuse, instead. unit must be repaired, first. Power supply or ballast might be shorted. To locate a fuse, you must look around the unit and find a little door, says: fuse. it might have a screw or two holding it, might not. Look at the fuse, first: if it looks pulverized, don't even dare to replace it! it will blow again and make more damage to the unit. If thin wire inside is just torn, then follow the procedure, described above. If the fuse is ceramic, you won't be able to determine, how it blew. Look at the fuse's rating: it might be written on a fuse door, or on the fuse, itself. could be from 5amp to 10amp, depend on power consumption. Remember: first, install the fuse with 1/2 of value: i.e: 6amp-put 3amp first, etc. Good luck with your project.
Thanks,
Alex.

Jan 07, 2012 | Panasonic PTAE2000U LCD Projector

1 Answer

I have a Sony vpl-1 projector that on initial start up it shuts itself off We have to keep cutting the power completely and start it again, this we have to do for around 4 or 5 times before it works...


If the projector has a lens cap, you have to help the projector to open it completely. Just use your finger and push the cap all ther way. On the projector I have this vis the case. there is a micro switch at the end og the lens cap opening mechanism.

gunnar.gronlund@nrk.no

Aug 29, 2010 | Sony Cineza VPL HS2 Multimedia Projector

2 Answers

Just stopped working. No LED. Changes the Lamp no fix! ANy clues


The first generation of the IN72 / IN74 / IN76 projectors had a power supply problem where a fuse on the P/S was under-rated. The 1amp fuse was subsequently replaced with a 2.5amp fuse to correct the problem. The reworked units have heat-shrink tubing over the fuses whereas the older 1amp fuses are bare. The fuse is located under the heatsink, about center of the board.

Feb 14, 2010 | InFocus Play Big IN76 Multimedia Projector

1 Answer

Want to change lamp


after you remove the door, the lamp assembly should be right ther with the little wire handle. unscrew the 3 screws and pull the lamp out. if none of that is there, you have no lamp to replace.

Sep 22, 2009 | Samsung Sp-H710AE Multimedia Projector

1 Answer

Hitachi CP-L850W lamp reset (No Remote)


easy on botem vent unscrew it then u see screw in ther holding balest of the bulb unscrew it litte pull up action on its arm as u will see lift it all out to get new in then reset timer ok

Feb 03, 2008 | Hitachi CP-L850W Multimedia Projector

Not finding what you are looking for?
Epson EMP 7500 Multimedia Projector Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Epson Office Equipment & Supplies Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18333 Answers

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2017 Answers

Are you an Epson Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...