Question about Turntables

1 Answer

Replacement stylus Hi Guys I am trying to find a replacement stylus for a sansui p-d10 turntable as I have been given the system but it doesnt have a stylus. Any ideas !!! cheers John

Posted by on

  • Anonymous Aug 16, 2008

    I have the Philco 841 205 3 in 1 and need a replacement stylus.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 20 Answers

I Can Go On Ebay ANd Search

Posted on Jul 27, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

BOSE 360 turntable manual


go google and type in --bose turntable spares --- and get a site that says spares like bose .com.au>en_au>support

or sansui-parts-shop.com
call on the phone or e-mail on the contact address

Jul 03, 2016 | Turntables

1 Answer

Sansui sr 333ere can I get a stylist for my sansui sr 333


If you look at the Cartridge it should have a make and model number on it. Put that into Google and it should find a replacement stylus.

Oct 31, 2013 | Turntables

1 Answer

I have a sansui FR-D25 automatic pll dc servo turntable. it hasnt been used in a couple of years due to a broken stylus. i have purchased a new one but now the metal plate sounds like its grating on the...


You will have to remove the bottom cover and pull the center post off. There is a set screw that holds it in place. Once removed you will need to clean the hole out of dirty grease and oil with a q-tip and alcohol. Then put some new oil in the hole. Just a small amount. Sewing machine or turntable oil or similar. Not motor oil! When put back together that will cause the platter to rise up and away from the base. You may also check the plastic gears under platter attached to the post to see if the are broken or cracked. If it is you have a major problem and it will need to be replaced with a donor part.

Aug 22, 2013 | Turntables

1 Answer

I changed the stylus in my DJ Tech 1000 turntable and now I have a much lower volume level recording onto ITunes. Any idea why?


HI, either the tracking weight is set too light or the stylus is not 100% compatable with your cartridge. Cheers john, Stylus City.

Mar 22, 2012 | DJ-Tech Turntables

1 Answer

When i play a record it skips and when i play it on another turntable the same record doesnt skip


Hi, most likely a worn stylus or the tracking weight is set too lightly. Adjust the balance weight at the back end of tonearm forward slightly. If no weight adjustment available put a very small coin on the end of tonearm above the stylus. styluscity@gmail.com

Jul 08, 2010 | Technics SL-1200 Turntable

1 Answer

Very low sound comming out pioneer pl300


Hi Jack.

Just confirm that it is plugged into a PHONO input (designed for turntables) Cannot use AUX/TAPE etc type inputs. If not, you will need an RIAA preamp from local electronics/Audio store. If that is OK, then try replace stylus first and the cartridge (may be just easier to do both same time). No volume control in turntables and it can only be 3 things (generally) Input, stylus, cartridge

Best of luck

Jul 24, 2009 | Turntables

2 Answers

I,m trying to replace my kenwood KD 47F turntable V68 catridge & N68 needle stylus with an Audio technica set due to non availibility of N68 stylus in my home country- singapore. Audio technica...


hi, any cartridge are posible in every turntable as long the needle is available...the wiring is the same the position ,, but the only thing that im not sure is the sensetivity of the needle ..some are not good but some is compatible..u

Jun 30, 2009 | Kenwood KD-291RC Turntable

1 Answer

Stylus will not catch


'Skating' is usually due to very low stylus pressure, which can be adjusted using a counterweight.

Is this the picture of the turntable ?
http://www.vintagetechnics.stereomanuals.com/turntables/sldd33.htm
Isn't that a counterweight at the back-end of the arm ? Can't it be rotated ?

If the counter weight is fixed, check the pickup mounting. May be it needs to be adjusted a bit forward (to increasing the stylus pressure).

Aug 20, 2008 | Technics Turntables

Not finding what you are looking for?
Turntables Logo

Related Topics:

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Turntables Experts

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

5653 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

411 Answers

Are you a Turntable Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...