Question about Samsung SyncMaster 753S 17" CRT Monitor

1 Answer

On/Off Power Toggle Switch is not working properly. When I press, it is on. But when I remove my finger, it goes off When i press again, it becomes on again. It beomes off again when i remove my finger

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 151 Answers

Plz change on/off button and check components around this switch
Hope this solution works

Posted on Jul 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My AOpen 19" LCD Flat Screen Monitor (Model F2915) is like new and works perfectly except for one thing. The push button power switch located on the top of the monitor has broken off and fallen insid


Certainly, if you jumper the connections to see which ones turn the monitor on or off, then you can go to an electrical supply place and get a micro switch and wire it in in place of the power button, or perhaps find a type that is flat that the power button can press. What you need to determine is if it is a push-on, push -off type switch, which always stays on or off depending on position or if it is a momentary interrupt switch where the button pressed momentarily turns it on and then releases and a second press connects the circuit to turn it off. You can do this by testing with your jumper wire, attach it and if the monitor stays on when you remove it, then goes off when you attach it again, you need the second type switch, if it goes off when removed, you need the always-on always -off first type switch. .

Mar 07, 2012 | AOpen F90GS 19 inch Monitor

1 Answer

MY COMPAQ 7540 17" MONITOR OPEN MENU AUTOMATICALLY


The buttons in front of your monitor is a toggle switch. This kind of switch is that when ' they get older they produces resistance and works with their own way, without pressing them. if you can do open your monitor you can do replace it.

1. prepare the following:
* screw driver/soldering iron/soldering lead/paint brush to remove melted leads.
2. remove all the toggle switch, replace all of it if possible, don't worry its really not expensive, it just cost about 12-15 pesos each.
3. then put in the new switches and try to put in the way it was before.
4. close back the monitor. this is 99.95% sure.

note: before doing these, unplug the wire from the outlet to avoid electric shock.

Jul 12, 2011 | Compaq CV 7500 17" CRT Monitor

1 Answer

Monitor connected to laptop... In power save. Can't get it to work


You switch from your laptop monitor to an ancillary monitor using the Fn key functions.

Press the Fn key, while keeping it down, press the requisite number key which has a small
screen printed on it, to switch back, repeat. It acts like a toggle switch.

Oct 08, 2010 | Dell IN1910N 19" Monitor

1 Answer

When I power off my LCD monitor, the screen goes all white, but once I turn the monitor back on it goes right back to displaying whatever it should on the screen. Or when I shutdown the computer it also...


If this has happened to two monitors on the same computer, then i dont think the problem is with monitors, i think the problem is with the graphics on the computer, i suggest uninstalling the driver for the graphics card in device manager and then restart the pc to see if that makes any difference. The divice manager in in the properties of my computer icon, just right click and choose properties, then device manager.

Feb 06, 2010 | Sylvania L181 18.1" Flat Panel LCD Monitor

2 Answers

MY MONITOR AOC LM725 GOES ON & OFF REPETEADLY ?


No, all you need to do is reset the monitor to factory settings. I fixed mine that way.
If your monitor goes off every 3 seconds (like mine did) you have to be fast or siwtch it on/off few times between the steps to get it fixed.

- 1st. unlock the OSD if when you press 'menu' you get the message 'OSD Locked'. To do this switch off the monitor, and press 'menu' while you switch it on again.

- 2nd. Switch it on, press 'menu' and quickly 'press '<' (left) twice and 'menu' twice to get it reset.

- 3rd switch it off and on again and if still goes off after 3/4 secs, try to reset it again.

I reset mine and it is working find. Before it went blank after 3 secs.

I just tried this because I did not understand why if it was a hardware problem I could see the screen for 2/3 seconds and if pressed on/off it came back, it made no sense as a hardware problem.

Dec 03, 2009 | AOC LM729 17" LCD Monitor

1 Answer

Can't get monitor to power on


I have a similar switch on mine, although mine is a Gateway. So my solution is going to assume the same indicators and functionality.

On mine, a blue-violet power switch indicates it is off, red indicates standby mode, and blue to indicate it is on and/or searching for a signal. When turned on (blue), the monitor will go to standby mode (red) after 3 to 4 seconds if it does not detect a source signal. So if you toggle the power switch to blue and it soon changes to red, you'll need to check your signal, cable, or possibly for a bad source connection on the monitor.

Oct 12, 2009 | LG L206WTY-BF Monitor

2 Answers

No picture after bypass of pioneer AVH-P4000DVD


remove the toggle switch and pray you didnt do damage to your delicate stereo system

Sep 27, 2009 | Pioneer AVH-P4000DVD Monitor

1 Answer

Blank screen


Possible that the HV inverter or the CFL tubes are going bad / defective. I suggest to bring the unit to an authorized Acer service center for proper check-up / test & fix the problem. regards

May 16, 2009 | Acer X221WSD Monitor

3 Answers

Im trying to bypass parking brake switch for pioneer AVH-P4000DVD. I already connected it to ground and then to power, but none of it works. I know that if i Install a toggle switch with 12volt current and...


This what you do. Connect the video wire to a power suppy and install a switch in the power wire. When you put the DVD in and the warning comes up, turn the switch on then off. This will allow you to watch the DVD without the park brake being applied.

Mar 21, 2009 | Pioneer AVH-P4000DVD Monitor

1 Answer

My monitor goes blank repeatedly


1. First u can check any dry points in power supply board and controlling circuit.
2. check all connectors (connected properly)
3.To replace front pannle Micro switches.

Oct 04, 2008 | Samsung SyncMaster 740N 17" LCD Monitor

Not finding what you are looking for?
Samsung SyncMaster 753S 17" CRT Monitor Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Computer Monitors Experts

Rugeshan Lanka
Rugeshan Lanka

Level 1 Expert

15 Answers

Pieter Vleeshouwers

Level 3 Expert

1410 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Samsung Computer Monitor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...