Question about Wurlitzer Jukebox CD Player

1 Answer

Have a Rowe Ami mmcd-1 jukebox but having keypad problems

The numbers 2 and 6 on the keypad are not being read. Sometimes if I reset the CCC (Central Control Computer) the 2 and 6 will work but only for a short period of time. The led lights are operating on the CCC to read that nothing is wrong. I checked the connections in the wiring from the keypad to the title strip keyboard interface and from there to the CCC, and everything is fine. I dont know if this is related but my title selection "flippers" do not work most of the time, but seem to work only when the number 2 and 6 on the keypad are working. I inspected the circuit boards, the keypad buttons do make a connection, I checked out the CCC and title strip interfact, but dont know what I am really looking for. Any advice?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 195 Answers

Hello,

Rowe Ami jukeboxes are prone to dry joints (called cold joints in the USA), this is cracking around the soldered connection pins that connect the wiringing to the circuit boards. If you can solder correctly then I would advise you to check all of the boards for cracking around any of the pins on the boards. So check out the following:-
Power supply board
CCC
Mechanism control/decoder
Keyboard

I would check out the Keyboard/Display the display board controls the title flip buttons.
I have seen a nuber of brand new display units for sale in the USA on Ebay for very little money.
When these were first made they were an arm and a leg. If you bought the combined unit that was put into the HML hideaways you could refit into your jukebox.

If You are not good at soldering then my advice would be send the boards to a Rowe Ami specialist for testing/repair.

Regards
Alan Hood
ami-man
UK

Posted on Mar 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My LN40C530F1FXZA give a massage that the USB 1/2 power overload, new device not found. also none of the HDMI are working. All other components work.


Just do a reset to this set, and then check. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; check the site linked here. Pull up older posts. http://electronicshelponline.blogspot.com/
Service mode entry, adjust and exit procedure to many popular brand TVs are given. Never forget to exit the service mode, after all adjustments have been done.

Jan 12, 2017 | Samsung LN40C530F1FXZA LN40C530 40 LCD TV...

1 Answer

Why won't my CD Player won't play CD's?


the laser that reads the cd is probably dirty - if you have a can of compressed air - insert the nozzle into the cd player and blast away any dust and debris - if this doesn't help - there are cd cleaning discs available at any major retailer - just insert the cd and it cleans the laser - worst case scenario - buy a new cd player - the prices have really come down - I replaced mine with the trim kit and wire harness for $100 - only took about 1 hour - but you do need to buy the Ford stereo removal tools (available also at any good stereo store)
6e3dbb0f-b64c-469d-81da-cd7b00f9f3ee.jpg

Aug 22, 2014 | Audio Players & Recorders

2 Answers

How to set the name plate on the brookstone electronic name plate


1) use a pin to press and hold "reset" to clear the display
2) press and hold "S" to get a blinking underline
for each letter, press the "C" triangle until you see the letter you want, then press the "E" square to enter that letter and advance to the next letter. when done, just wait for it to timeout.

I'm unsure how to display things more than 16 letters.

Aug 11, 2014 | Audio Players & Recorders

2 Answers

I have a Rowe R80 jukebox and after moving it it has no sound through the speakers I am in New Zealand


Well, in addition to all the fine suggestions that are here, I would like to add the simple and easy things that may have happened during the move.

IF YOU ARE NOT GETTING A LOUD POP WHEN THE MACHINE IS POWERED ON.......

1) Make sure that the wires on the terminals below are still connected to the screws. There is one ground and one each for left and right. The lower the tap the lower the (max) volume of the jukebox.If they are not connected there will be no sound.
84c9065c-b7c6-4417-be21-0be7a6e74b41.jpg


There is a jumpers on the terminal strip where the volume control connects. Make sure that these connections are correct and tight. Also make sure that the jumpers did not fall off.
c1d72051-525d-47ec-8725-a6a8e655b20c.jpg
7a25e260-d39b-4992-8bce-8c2d2c9b07e5.jpg

If you are getting the loud pop in the speakers when the power is turned on .....

Check the plug on the side of the mechanism, just below the back of the tone are.(looks like a little tube socket) Check to see that it is connected to the mech and the CORRECT PLACE on the amplifier. It mat be possible to have this end in the wrong place. bf77613e-82a3-4e37-b8fe-cc80f4d4dbcb.jpg

Check all all your connections against the pic.

I hope this was helpful.

Mar 24, 2014 | Audio Players & Recorders

1 Answer

How to reset my combination lock number on ipod A1236


Hi William
If you have forgotten the code or put the wrong code in your ipod, you can unlock the Ipod by doing the following:
Connect your IPod to the primary computer you use it with (the first one Ipod synced with), and open iTunes.
When you disconnect iPod from the computer, it will no longer be locked.
If you can't unlock Ipod using either (the code or connecting it to the computer you use to manage its songs). . . you can restore your ipod to factory settings using ipod Updater.
Please note that this will erase all data on your ipod.
Afterwards, you can add your music and data back to your ipod.
If you want to change the primary computer that your Ipod is associated with, do this:
1. Restore your iPod. WARNING: The restore process cannot be undone.
All of your songs and files will be deleted.
Always make a backup of your important data.
2. Connect your ipod to the computer that you want to be the primary computer.
3. Open iTunes and synchronize.
If you can't unlock your ipod and you don't have access to the primary computer, your only option is to restore the Ipod, which will erase all music and data.
Please take time to rate me
Bud

Apr 03, 2013 | Audio Players & Recorders

3 Answers

Flashing blue light


1. turn it off2. hold centre button until blinking blue and red3. briefly press volume down4. turn it off= fixed :)
From Sennheiser UK:http://www.sennheiser.co.uk/uk/home_en.nsf/root/contact_menu_technical-question_telephone_headsets_faqs_mm400_series_bluelight

Jun 19, 2012 | Sennheiser MM 550 Wireless Headphones

1 Answer

I have a 1970's Panasonic Flip Clock Radio. (Model RC6530) The radio works just fine, but the flp clock stopped flipping. There is power going to the unit. I can also hear a low hum from the flip...


It looks like your problem might be an easy fix, at least. If the gear train between the motor and clock got stripped, you'd be in a bit more trouble. If the motor just isn't spinning, remove it from the side of the clock housing. There are 2 screws (or nuts) holding it in place. When you get it off, the cover for the motor will also be off. Apply some 3 in 1 oil, or perhaps just a tiny bit of penetrating oil, and give it a spin. From what I've read, it should do just fine. A lot of people use wd40, but I understand that can gum up over time.

This is a "at your own risk" type of repair, but as long as you unplug it before dismantling the radio, I think you'll be fine.

Feb 10, 2012 | Audio Players & Recorders

1 Answer

Wailing sound when 1971 seeburg juke box is started


I amnot very familiar with Seeburgs but the trip switch activates at the end of the record playing and THAT mutes the amp. The amp should also be muted until the tone arm lands on the record. So I would suggest the problem is in the amp.

May 05, 2009 | Audio Players & Recorders

5 Answers

BOSe Wave Radio - Disk "not readable"


I had the same problem with the disk unreadable error and took my unit to a authorized repair dealer about 100 miles from where I live to have it fixed. It ended up costing me about $300 to have the CD unit totally replaced which is almost as much as I paid for the unit in the first place. I am like a lot of you that used the CD very little although the unit was about 3 years old. I think Bose has a problem and would like us to think it is very rare. I bought a Lifestyle surround system about 14 years ago that has a CD and have never had a problem with it so needless to say I am very disappointed in the Wave II Radio/CD system. I am fairly certain the problem will occur again, but only time will tell.

Mar 03, 2008 | Bose Wave Radio

Not finding what you are looking for?

Open Questions:

See all Wurlitzer Jukebox CD Player Questions

Wurlitzer Jukebox CD Player Logo

668 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wurlitzer Audio Players & Recorders Experts

phil

Level 2 Expert

567 Answers

Rick

Level 2 Expert

611 Answers

The Knight
The Knight

Level 3 Expert

69845 Answers

Are you a Wurlitzer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...