Question about KitchenAid Cooktops

1 Answer

KECD805HBL3 I have the above mentioned Kitchen aid cook top. The front right burner will not turn on. The other 3 work fine. Any thing I can check? and how? Best Regards, Bobby

Posted by on

  • Anonymous Mar 16, 2014

    I was using the cook top on the stove and it worked fine, one I turned the burners off, my screen showed E-2 code and it kept beeping, I cannot set the clock or turn on the oven at all. What would cause this?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 59 Answers

Hello
I have the folloing Manuals in PDF format, I will gladlu email them to you.
KECD805HBL3 - pdf_icon.gif Use & Care Guide Dimension Guide pdf_icon.gif Installation Guide
Eddie Rentas
Tupper Lake NY

Posted on Jul 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

GE cooktop ignitor jgp


Look for a short in the wiring (usually white wires running to the ignitors) or a loose ground wire. (usually green)

Jul 02, 2012 | GE Cooktops

1 Answer

Kitchen aid KECC507GBL3 electric 36in cooktop. Burner switch is out - cannot get glass top off. Have removed all screws from plate mountings on the sides. Is there a trick to this?


Hi,

If it’s a range, there is usually a couple of screws that hold the front of the top down, remove the screws, lift the front of the top and pull it out from the back hinges. Install the new top, make sure there are no loose wiring.
If it’s a cook top then make sure that the power to the cook top has been turned off, open the cabinet and look up. There should be a couple of brackets that secure the cook top. Remove the brackets, carefully lift the top and set it on the counter top (put a towel on the counter top first). replace the glass top (make sure there is no loose or exposed wiring), set the cook top back in the counter, secure it with brackets as was before, and double check your work.

Thanks for contacting fixya.com

Jan 14, 2010 | KitchenAid Cooktops

2 Answers

Hi I have a kitchen aid cook top and need to replace the gas knobs part #KIP5692-3182567 Can you direct me on how to purchase four knobs. Thanks Frank


hi frank
goto appliancepartspros.com
or call 1-877-477-7278
your looking for part number
AP3140295
thay run around 10.00 bucks a pop
hope this helps

Oct 16, 2009 | GE JGP930SEDSS Gas Cooktop

1 Answer

Spark igniters continue to spark:


let it all dry out

thumbs up

Aug 17, 2009 | Cooktops

2 Answers

G.E Profile gas cook top #JGP640 ignitor.


It is sparking because the module does not sense the heat which would normally cause the sparking to stop.

It can be caused by a poor ground, make sure the ignitor at that burner is clean and free from any obstructions. If it is then it could either be a defective ignitor or spark module.

Mar 12, 2009 | GE Cooktops

1 Answer

Viking Gas Burner issue?


is this a sealed burner unit? if so the burner base (the heavy brass part under the burner cap) has to be sitting just right. you will notice that it has holes around the the sides make sure that where your ignitor sparks to it that it aligns with the lowest hole on the burner base. if you have a great flame all around the burner after checking what i mentioned i would replace the spark module. if it continues to drive you crazy with the noise - just unplug it. the burners will continue working fine without power.

Dec 23, 2008 | Viking 42 in. Professional Series...

1 Answer

Jenn Air gas cooktop


pop me an email at b4829@yahoo.com and reference your cook top you can rate me later

Mar 29, 2008 | Cooktops

2 Answers

One unit show fault code F153


Hi - I've been having the same problem. GE tech service in St. Louis, MO has been a joke. 1st tech call cancelled 30 minutes before appointment. 2nd tech call to diagnose the F153 code I had already provided when I scheduled service on-line cost $74.95 and the tech didn't have the part on his truck. 3rd tech call a new tech shows up, has no knowledge of previous call diagnosis, opens the box sent to my home by GE and announces that the previous guy ordered the wrong part! We're on the 4th call. My cook top right front burner has not worked for a month. I've contacted GE corporate. The part you need (at least I need) for the right front burner which is a large burner is: WB30T10062. If I knew how to, I'd repair this myself. I don't have the extended warranty. The part is covered because my cooktop is only two years old (parts warrantied for five years) but labor is estimated to cost almost $200....plus the $74.95 "diagnostic" visit. A total rip-off. My advice, if you've got this cooktop, it's still under warranty and you aren't using all of the burners on a regular basis: start using them! The tech guy said most people use that front right burner alot and it eventually malfunctions (code F153). His suggestion was to start using the other burners on a regular basis, too, so that when they go out, at least the part will fall under the five-year warranty! When this cook top is done, I'm going to get a gas stove with "old fashioned burners" and it won't be GE!

Sep 24, 2007 | GE 30 in. Profile JP938 Electric Cooktop

Not finding what you are looking for?
Cooktops Logo

Related Topics:

332 people viewed this question

Ask a Question

Usually answered in minutes!

Top KitchenAid Cooktops Experts

doug2008

Level 2 Expert

101 Answers

freddyfox

Level 2 Expert

236 Answers

Brad Brown

Level 3 Expert

13576 Answers

Are you a KitchenAid Cooktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...