Question about Krups 203 Grinder

2 Answers

Krups coffee mill

Coffee mill stopped grinding. How do I take it apart to check for loose wires?

Posted by on

  • tahoejim59 Jul 23, 2008

    Krups Type 203 B Household Coffee mill, stopped grinding. How do I access inside?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

There are four slots in the bottom through which you can see the attachment clips. These clips are not mounted on the base but clip into the base. There is a special 4 prong tool that is used to depress these but if you don't have one, which you most certainly will not have, you need to use four small nails to open it up. Looking at them from the bottom, the clips look like a capital E with an extra horizontal leg. try to drive your nails in to the middle of the back of the E, that is on the flat side. After you have done this use a claw hammer to pry the bottom off by inserting the claws into the seam between the bottom and the top and twisting until something gives. You will probably get the bottom off without destroying more than one of the clips. No matter, you can tape or glue the ****** back together.

If power lose was your problem, remove the switch from its clip then test it to see if depressing the button causes the contact rod to touch both of the copper plates which are mounted on opposite sides of the switch, be careful while making this test - you have to have the grinder plugged in and you do not want to be touching any electrical contacts, the blade or the motor. Also beware of the torque from the motor causing you to drop the grinder. Also, beware of the torque from the motor causing you to drop the grinder in the unlikely event that it is working.

If depressing the switch doesn't cause the switch shaft to come in contact with both plates then get a pair of plyers and bend the copper plates down so that contact can be readily be made.

Retest to confirm the fix works then reassemble, using tape, glue or whatever and then -- it's coffee time!!

Posted on Jan 31, 2011

  • Todd McC
    Todd McC Jun 25, 2012

    Good luck getting those tabs to unclip w/o breaking them! I just found the problem though the switch has 2 copper tabs that make contact with its little cone button, there was metal eaten away from the button from arcing and one of the copper tabs was also half eaten away I just twisted it 90 degrees then bent the copper tabs down as much as possible voila! put together still working...

×

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

To disassemble the Krups 203B grinder locate the four recessed clips which snap into the base. Tip the unit over and look at the base. I was not able to unsnap these without damaging the clips. Once the clip ends were removed the base and top separated easily. The AC cord is soldered to two connections. The cord was easily shortened and resoldered solving the intermittent power problem. The base and top were reassembled and a small amount of glue in a few locations secured the base to the top.

Posted on Oct 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can I grind coffee in an electric grain mill?


Electric grain mills were not designed to grind up oily grains like coffee, you would be better off getting either a hand grinder or a coffee grinder.

Jan 23, 2014 | Kitchen Appliances - Others

1 Answer

How do I clean my burr mill (Models BMX3, BMX4, BMX5 and BMX6)?


Clean your burr mill before using it for the first time. Then, to ensure optimal mill function and durability, clean it regularly following these simple steps.
  1. Always unplug your burr mill after use and before cleaning.
  2. Open the hopper lid. Empty any whole beans from the hopper. Remove the top burr mill by rotating it clockwise. For better results hold the grind setting button while rotating the burr mill clockwise. This will allow you to clean the grinding wheel and the grinding compartment.
  3. Clean the interior recesses with a soft brush. Note: Never use water or liquid for cleaning the lower grinding section of this appliance. BRUSH NOT INCLUDED.
  4. Wipe the whole bean hopper, its lid and the mill exterior with a damp cloth.
  5. The ground coffee chamber and lid can be washed in mild detergent and water. They both are top rack dishwasher safe. Do not immerse the mill or the whole bean hopper in water or any other liquid or place in dishwasher. Use only non-abrasive cleaners to remove stains.
  6. After completely drying the whole bean hopper and top burr mill, replace the burr mill in position by aligning snaps with receptacle and rotating counterclockwise to lock it in position. For better results, hold the grind setting button while rotating the burr mill counterclockwise. Once the burr mill is in position, pull gently to check it is properly locked in position. If the burr mill comes out, repeat this step again.
  7. Replace the ground coffee chamber and lid, making sure both snap securely into place.
  8. Fill the hopper with whole beans.

Sep 02, 2011 | Bunn NHB Coffee Maker

1 Answer

My Cuisinart CCM-16PC suddenly decided not to burr/grind coffee. It doesn't turn on. Electrical recepticle is hot and the device is plugged in. I've cleaned all of the connections/buttons/grooves so...


Same thing happened to me about 1 year ago. I took the machine apart and determined the issue to be in the circuit board. I bypassed the board and wired the power cord directly to the motor. The machine began to work and is still operating fine. The only drawback, of course - having bypassed the circuit board and switch, you now are on full manual operation. Plug the power cord into the wall outlet and the motor spins; when you are finished grinding you have to remove the cord from the power source to stop the motor. I am OK with this - beats 35 - 50 dollars for a new grinder. Dave

Feb 28, 2011 | Cuisinart CCM-16PC Supreme Grind Automatic...

3 Answers

Grinder stalls constantly (motor whirring, but no grinding happening) so I shake it to get it grinding again, but the whirring/no grinding happens over and over. I have to shake the think 5 or 6 times to...


As I can see, what happens is that some coffee grains stucks in the way from the upper pot to the grinding wheel. This is not something usual, but possible if coffee grains are too big and are placed across the entry of the mill. Try cleaning more deep with some old toothbrush. Look for a clean and even surface of the duct.
Other cause might be a loosen mill hub/grinding wheel off the motor shaft, which would require dissassemble of the appliance to be repaired.

Dec 10, 2010 | Krups Burr Coffee Grinder

1 Answer

No coffee is coming out of the machine...


in our machine we wanted a stronger coffee so we adjusted the auto grinder (where the coffee beans are housed) to the finest setting thinking the finer the grind the stronger the coffee...after doing this the machine wouldnot make coffee...we sent it away while still under warranty and the tech said that the grind selection was too low so they just turned the grinder back up a notch and it worked fine ....dont know if this will help but it's worth a try!

Mar 26, 2009 | Krups Orchestro Dialog FNF2 Espresso...

1 Answer

Grinder starts up but wont grind..nothing happens. one week old


I think this might be because no beans have gone down into the mill. There is a definite difference in sound when it is actually grinding beans. Try emptying the beans out, set it to the coarsest setting, put the beans back in, shake the thing a bit then turn it on.

Jan 17, 2009 | Krups Burr Coffee Grinder

2 Answers

GVX2 krups coffee grinder; how to open it?


I have the same issue. You need to take both dials off, then on the bottom, there are 4 tabs on the inside. Seperate the halves and you will see them. Towards the front and halfway back. Pry the halves apart enough to push the top towards the bottom and it slides apart pretty easy. The tricky part now is finding the replacement part. I have super glued my switch and I want to do something to try and repair it further. Maybe epoxy. I called Krups and they can't sell the part to me. I called one of their service centers and they can't sell the part to me. So, if someone knows where to get the part, I am all ears :)

Nov 25, 2008 | Krups Burr Coffee Grinder

2 Answers

Lots of disturbing noises, no coffee


It is is easy, if you know how to do it... as always
First take of the wather, trach bin etc,
Start with removing the cup wher the beans is stored, the adjustment knob for the mill is a tricky part. Remove it by bending out the side of the knob. Thereafter remove the screws from cup and those you on see on the top.
The front (silver frame) is removed by lifting it upwards, behind it you have 4 screws that has to be removed.
The last two screws is found under the wather tank.
Now you should had take away 11 screws, at least...
Bend the back of top and it will be off. Finally push the rest of the plastic cover backwards.

Do you know what the error codes says? I have know 6,8and no coffy...

May 11, 2008 | Krups Small Appliances Espresso Machine

1 Answer

Krups Orchestro Dialog coffee machine


that mean no coffee go through us if you dont use the machine often you might have coffee residue on the grinder teet remove the coffee bean in the hole were the coffee bean goes use a brush and clean the grinder teet very good with the residue of coffee gonna grind and gonna go through thanks for usig fixya pierre

Feb 07, 2008 | Krups Orchestro Dialog FNF2 Espresso...

Not finding what you are looking for?
Krups 203 Grinder Logo

3,036 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

cyfred

Level 1 Expert

3 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...