Question about Tag Heuer AquaracerWAF1110.BA0800 watch

Open Question

When I place into stopwatch mode, the hands do not reset to zero. When I place into settings mode, the hands do not match the place they should be. The small hand that denotes the date goes past the number nine around into the dial face, but will not go below 3 when trying to set

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Resetting stopwatch dials - Armani AR5331

The 24 hour face on the right of the watch is the time, not the stop watch. The minute timer on the left of the watch face is the minutes for the stopwatch, if this is not resetting to 0 after holding down the lower button on the right hand side of the watch, contact your manufacturer.

Posted on Mar 04, 2008

Ad
escapement
  • 2334 Answers

SOURCE: Resetting stopwatch dials - Armani AR5331

When you reset the big seconds hand to zero, the hour and the minute hand are not engaged in this function, so, there is no fault with the watch movement.
Do as follows:
1) pull out crown and set the hour and minute hands at 6 o'clock (they must be lined perfectly in opposite directions)
2) push the crown in half way back (not completely)
3) push and hold the button at 2 o'clock (set the big seconds hand to zero) and release it when done
4) when big seconds hand is zeroed push the crown back in
5) pull the crown out again and set desired time
6) push the crown back in.
If all actions described do not work, you will have to visit your nearest watch repair shop and ask to refit chronograph hand as in this case it is out of balance (not pointed at exact mark).

Rate me, please.

Posted on Apr 03, 2009

  • 122 Answers

SOURCE: stop watch will not reset to zero

pull the crown full out reset all hands set time set alarm or second time if you wish and press the crown back.

Posted on Mar 15, 2010

  • 22 Answers

SOURCE: my tag heuer carrera stop watch doesnt reset

Try this.

Pull the winder out fully. Then press the top right chronograph button to move the centre seconds hand on. Then push the winder back in.

on some models you should only pull the winder half way out.

good luck

Posted on Sep 23, 2010

gopakumarg43
  • 75169 Answers

SOURCE: I have a tag link automatic CJF2112 and the

Hello
Get this U-Tube link, where all adjustments to your watch has been show. If you need any further assistance, contact the nearest Tag Heuer service center at your town. No user repairable options left with this device.
www.youtube.com/watch?v=alnkRZDHams
OK

Posted on Jul 21, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Stop watch will not reset to zero


pull the crown full out reset all hands set time set alarm or second time if you wish and press the crown back.

Dec 01, 2009 | Seiko Coutura Chronograph Watch

2 Answers

Stopwatch


You need to calibrate it. In normal time mode, pull the crown out all the way and then use the pushers to step it back to the zero position. When finished, push the crown back in. You can also calibrate the sub-dails in a similar fashion.

Mar 31, 2008 | Navy Seal Luminox Watch

3 Answers

I have a seiko chronograph sports 150 watch; had the battery changed a few day ago and just noticed that the second hand & stopwatch hands are not 'centered'. is ther a way to reset this ? cheers


As jimmyguru said.
1. Pull the crown to the second position (all the way out)
2. Push and hold the reset button and allow the chronograph hand to rotate near the 12 o'clock position.
3. Release the reset button.
4. Repeatedly push and release the reset button to find tune the hand position until it is right at 12 o'clock.
5. Push the crown back in.

Nov 05, 2009 | Seiko SNA553 Alarm Chronograph

1 Answer

Resetting stopwatch dials - Armani AR5331


When you reset the big seconds hand to zero, the hour and the minute hand are not engaged in this function, so, there is no fault with the watch movement.
Do as follows:
1) pull out crown and set the hour and minute hands at 6 o'clock (they must be lined perfectly in opposite directions)
2) push the crown in half way back (not completely)
3) push and hold the button at 2 o'clock (set the big seconds hand to zero) and release it when done
4) when big seconds hand is zeroed push the crown back in
5) pull the crown out again and set desired time
6) push the crown back in.
If all actions described do not work, you will have to visit your nearest watch repair shop and ask to refit chronograph hand as in this case it is out of balance (not pointed at exact mark).

Rate me, please.

Apr 03, 2009 | Watches

2 Answers

Festina Dashboard watch - Adjusting the hand of the stopwatch


Your watch has quartz movement and stopwatch adjustment by one step (one full second) only. That means you will not be able to adjust stopwatch hand by using pushers on your watch as each push of the pusher will advance stopwatch hand for the full second, not the fifth or the tenth of the second, and the hand will stay slightly off anyway.
This happenened because the IC (integrated circuit) in your watch miscalculated the teeth count on chronograph wheel and stopped one or two teeth past or under the zero point. It doesn't happen very often, but in your case it did and the only solution is to find your nearest watch repair shop and ask for resetting stopwatch hand to zero.
This procedure needs partial disassembling of the watch and quite a great skill as the stopwatch hand must be removed and then refitted with great accuracy. All this needs to be done by very specialized tools as well.
I think this is the only solution of your problem unless you can live with that and just leave it as it is.
Do not forget to rate, please.

Feb 09, 2009 | Festina Dashboard 6719/3 Watch for Men

2 Answers

Tag Heuer Link, stopwatch seconds hand stops 2 seconds before 12


Pull crown out to position 2 [in between unscrewed (1) and pulled all the way out (3)].  Tap Button B (bottom) to reset by step back to zero.
Incidentally, Button A works Hours register in same manner for position 2.  You can similarly reset second and 1/10th with Buttons A and B, respectively, while in position 3.  Cheers! 

Jul 25, 2008 | Tag Heuer Link Automatic Chronometer...

1 Answer

Re-set quartz chronograph sweeping second hand


Easy Soultion worked for me. Believe Me I was worried only had the Seiko Sportura for a week now. My second dial for the stopwatch was re-setting to 5 seconds instead of zero. The Solution is
1. pull the Crown all the way out ( In the position you take the crown to set the time , second click ).
2. To set the minute face of stop watch , keep pressing the top button untill it is zero. To set the second needle to zero keep pressing the bottom button untill it reaches zero or where you like it to re-set each time. Depend on you.
3. Once all neddles of stopwatch are at resting postions ( usually zero) secure the crown back to its normal postion. Test your stop watch , hopefully it will go back to zero when you press the reset button. C

Glad to help. ashfaque.r@googlemail.com

May 18, 2008 | Seiko SNA553 Alarm Chronograph

5 Answers

I have a seiko flight watch, unknown of the model, second hand doesn't reset


I guess the blue faced SEIKO is a Flightmaster (Model: 7T92- OCFO)and it is a great watch. This is a common problem with most chronographs and this happens due to misalignment with usage.

All you need to do is pull out the locking crown all the way out (2nd Step) as if setting time. and then press and hold the top / left button and at first the milli seconds hand resets. after which you have to press the borrom / right button to move the seconds hand in to place. and then reset the time and lock the crown. You can repeat this for Milli Seconds, Seconds, Minutes & hours hands.
Hope this helps,
Krishna Chaitanya GT.

Apr 27, 2008 | Seiko 0512039FA Wrist Watch

2 Answers

Resetting stopwatch dials - Armani AR5331


Pull the crown to first position (where you set the date) then adjust the dials with buttons.

uhrmacher

Jan 10, 2008 | Giorgio Armani Classic AR5326 Wrist Watch

3 Answers

Reset Stopwatch Hands on CL1111 ?


Try setting the crown to position 2 - i.e. the position normally used to adjust the date.  Then use the top and bottom stopwatch buttons to adjust the minute hand and 1/10th hand respectively.

Oct 18, 2007 | Tag Heuer Aquaracer Quartz Chronograph...

Not finding what you are looking for?
Tag Heuer AquaracerWAF1110.BA0800 watch Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tag Heuer Watches Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18424 Answers

The Knight
The Knight

Level 3 Expert

75169 Answers

Jimmy Accardi

Level 2 Expert

101 Answers

Are you a Tag Heuer Watch Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...