Question about Symbol PPT 8800 Wireless Barcode Scanner

1 Answer

Align Screen Dear Fixya, Why my pocket pc always asking about align screen? i have already taped it more than ones, but it keep showing the align screen? Thx

Posted by on

  • Anonymous Mar 24, 2009

    I have been tapping for ever please do help


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 97 Answers

It will need a new screen. This is a common fault on this type of terminal and since the touch pannel is incorporater on the screen assembly, that is the only solution.

You could always try a software update from IPL mode, however is not very likely that it will resolve the calibration issue.

Posted on Apr 01, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Mc9000 stuck on align screen

Contact Motorola Solutions.
Get Support

Motorola Mobility Support

May 12, 2014 | Motorola Computers & Internet

1 Answer

The align screen for MC9090 is not calibrate. Already calibrate but still the touch screen is not proper.

Hi you need a replacement digitizer. The unit may have been dropped hence the reason it is now faulty. please contact for repair. 00441179064587

Aug 05, 2011 | Symbol MC9090-G Barcode Scanner

1 Answer

SanDisk Sansa Clip will not turn off. Screen lit, muSic info ShowS, no reSponSe to controlS including on-off button. Battery ShowS fully charged.

two things to try....

the first wil be to connect unit to PC using USB cable. let it sit for a few minutes then uplug and see if it resets itself.


there is a little inset reset button on unit, usually onback or bottom. use a papr clip to press in and hold for about 10 seconds.

This should also reset unit.

Hope this helps


Please rate FIXYA

May 24, 2011 | Computers & Internet

1 Answer

Keep on paper jam everytime i try to print paper feeder not align help me pls how to fix this one

check for something they may have fell into the feeder like peice of paper or thumbtack anything that would obstruct the paper path.

May 04, 2011 | Computers & Internet

1 Answer

My son's laptop just goes to the start up screen but won't start up, it just keeps showing the circle and saying welcome


start your laptop and keep pressing F8 until safe mode screen shows and choose for last good known configuration and enter. your laptop will start at the last time it is working good.


Mar 27, 2011 | Computers & Internet

1 Answer

Printer says "incorrect alignment" and

Possible causes of the error you got can be that one of the ink cartridges is low or out of ink or the paper has already been printed on or is colored paper or the ink cartridge is defective.You need to
examine the paper the alignment page was printed on. Does the alignment page print correctly?You need to perform an print cartridge cleaning procedure and Try to align the page again.

Mar 14, 2011 | Computers & Internet

2 Answers

The print screen button doesn't seem to work....

The PRINT SCREEN key (prt sc) copy the screen from your pc at the clipboard. After pressing this key you have to start an image editor software (or Microsoft Word) and paste the copied image.

In case of a problem or clarification or further details needed, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Thanks and regards
Please kindly rate this solution
direct fixya link:

Mar 01, 2011 | Computers & Internet

1 Answer

Computer will not boot past POST and it shows "CMOS checksum error - defaults loaded" on the screen...

good day,

your cmos battery is weak(low voltage) it does not save your bios settings every time you configure it or set it to default settings, it will always display cmos error every time you shutdown your PC, try replacing it with a new one, check the old battery model and buy it in your nearest computer shop, commonly used battery in Motherboards is CR2032 Lithium battery..

Hope this helps.

Sir MArkus

Feb 01, 2011 | Computers & Internet

1 Answer

When i turn on the computer the windows xp load screen comes up as always but this time it keeps freezing so i cant get into my computer

Try to boot in safe mode and check wether its entering in the windows, if its work then choose privious restore point & restore your pc. also remove any unwated software, keep the HDD free from excessive fragmentation, as this may help prevent startup problems, freezeups, crashes etc.

Jul 20, 2010 | Computers & Internet

Not finding what you are looking for?
Symbol PPT 8800 Wireless Barcode Scanner Logo

Related Topics:

611 people viewed this question

Ask a Question

Usually answered in minutes!

Top Symbol Computers & Internet Experts

Gareth Cockram
Gareth Cockram

Level 3 Expert

657 Answers


Level 2 Expert

254 Answers


Level 1 Expert

20 Answers

Are you a Symbol Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides