Reset button not working - U.S. Robotics (USR8054) Router

Have you tested the reset switch for continuity?? That would be the perfect place to start. If it's open, replace the switch, if you have continuity it's a board issue

Replace the reset button or bypass it.

power it off if you a reset button next to the usb use that to reset and the power button to reset

if that doesn't work try this
To reset the device, press the power button and the volume down button and hold both of them for 10 seconds. Once the tablet turns on it enters the Reboot screen. Scroll down to "Wipe Data/Reset".
you will your data with this reset

With tablet off, Hold power and volume+ buttons together until reset page comes on, then select factory reset!

Are you trying to do 30/30/30 reset??

THIS WILL RESET TO FACTORY

You have to do this.

THere is in the back a reset button.

With the router on.

NEVER RELEASE THE RESET BUTTON UNTIL FINISHED.
1. HOLD THE RESET BUTTON FOR 30 seconds by watch
2. PULL OUT THE POWER CABLE while still holding the RESET BUTTON for 30 seconds.
3. WITH THE RESET BUTTON STILL PRESSED plugged in the power cable and continue holding for 30 seconds.

4. Then release RESET.

Hope it works.

God Bless You!!

error 27???
you can reset your printer..
1.with the printer powered off but connected to a power source,press the power button while pressing and holding the stop/reset button.
2.when the power is lit,press the stop/reset button two times while pressing and holding the power button.
3.when releasing the power button and stop/reset button(regardless of order),the printer will move into service mode.(wait for menu selection)
4.when the on/off light is green,press stop/reset button the specified number of time(s)according to the function listed in the table below..(each time the stop/reset button is pressed,the led lights alternately in orange and green,starting with orange.)
note:press 4 times for waste ink counter reset..
if did not work try more..
not work again you can change the sponge...

Hi you can try this may work.

In service mode.
Put Stop/reset 4 times orange => reset waste ink.
Put stop/reset 8 times orange => set level ink.

And try this.

1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.

For me, it worked when I did this:
1) With the printer powered off but connected to a power source, press and hold the Stop/Reset button for 4-5 seconds.
2) Without letting go of the Stop/Reset button, press and hold the Power button. Then, press the Stop/Reset button two times without letting go of the Power button.

Please come back and just gave a vote, it will gave me some satisfaction to know am helping some one so I will keep on helping.
All The Best: Pineworks

Was there any power flicker before it happened?

1. Reset the router by pressing the reset button of the router for 15 seconds while the power cord is plugged in and while the router is powered on.
2. Release Reset button after 15 seconds and unplug the power cord of the router then press the reset button again for 15 seconds.
3. After 15 seconds release the reset button and replug the power cord then press the reset button again for 15 seconds.

If this didn't work.
1. Plug the power cord to the router, and unplug it do this 7 times then reset for 15 seconds while it's unplugged and plug it back it and press the reset button for 15 seconds and release it. Try to check if there's any changes.

You can reset this Wireless Access Point by clicking on Reset button, and then press OK button to confirm your decision.

Note: you can also hold down the reset button for more than 10 seconds to reset its default settings back to factory default.

If the reset doesnt work turn off router then on again first, but if the reset doesnt work, the router may need to be replaced.

If there reset the router to the factory settings:
Default Username: admin (lowercase)
Default Password: none (none, leave blank)

If this doesn't work, try pressing the reset button for 10 seconds with it powered ON. Then try it off. I can't remember which one will work.

After this is complete, username: admin and password: (nothing, blank, nada) will work.

Good Luck!