Whenever i start my computer i find my time to be 12:00 1st jan 2002 how can i set it

Help with spark Plug placement/firing order - KatRiders.com

https://katriders.com > forum > mechanics-101 > 7417-...

Dec. 7, 2005 - Hello my son has bought a 94 Katana GSX600F he removed all the spark plug wires and dont know how to put the new ones on also he only ... 11 posts · Left coil is for 1 and 4 , right is for 2 & 3 . Are the leads still hooked up to the coiils ...
2003 GSX600F Spark plug wire order
7 posts
Mar. 11, 2012
Firing order.
6 posts
Jan. 18, 2005
Bike keeps misfiring...
15 posts
Jan. 1, 2012
94 Katana GSX600F Starting issues
15 posts
Apr. 3, 2013
More results from katriders.com

Diagrams

https://www.google.com/search?q=2002+katana+600+firing+order+diagram&safe=off&rlz=1C1QJDB_enCA643CA644&sxsrf=ALeKk00HCWDgEGn91hmDmM2ghqYLefOvUA%3A1619131634342&ei=8vyBYJ2nFMO0tQbyuKbACQ&oq=2002+katana+600+firing+order&gs_lcp=Cgdnd3Mtd2l6EAEYADIICCEQFhAdEB46BAgAEEM6AggAOgQIABAeOgkIABDJAxAWEB46BggAEBYQHjoFCCEQoAE6BAghEBU6BwghEAoQoAFQ9-EBWKSTAmCZvwJoAHAAeACAAfIBiAGPCpIBBTYuMi4ymAEAoAEBoAECqgEHZ3dzLXdpesABAQ&sclient=gws-wiz

..

replacing timing chain???...Costs??? - Ford Explorer

www.explorerforum.com > ... > Stock 2002 - 2005 Explorers

Mar 20, 2008 - 8 posts - ‎5 authors
Stock 2002 - 2005 Explorers. ... What is the reccommneded time to replace the timing chain in a '02 Explorer 4.0 ... Costs inc. mechanics labor? Timing chain replacement cost on 2003 Ford Explorer ...
2 posts
Dec 2, 2011
Timing chain rattle resolution process - SOHC V6
19 posts
Jul 6, 2011
Timing Chain Replacement Cost - Ford Explorer and ...
6 posts
Jul 28, 2010
4.6L Explorer engine timing chain ooops! - Ford ...
19 posts
Jan 10, 2008
More results from www.explorerforum.com

Estimate of cost for a timing chain replacement - 2003 Ford ...

When you get the BIOS POST screen you need to press either "f2" or "Del" then look for the "Default setting" selection. The chances are that the cmos battery has failed. a new one is very cheap and easy to fit. It about the size of a Quarter or a ten pence piece. Good luck.

Some of these cameras cannot save the date, and has no internal battery to save the data. The best solution I have use is to buy another battery with these kinds of cameras and always have one charging, or take two batteries when you take pictures.
These older point and shoot cameras are nice, and slower than the newer ones, but will not save the data unless you keep the main battery in it, or replace the one to be charged with another battery within a very short time.

Whenever the 'CHECK ENGINE' (Service Engine Soon) light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on.
You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code which have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE the problem and perhaps eventually fix the problem.

NUMEROUS POSSIBLE CAUSES! Does the Check Engine light come ON when this happens? Whenever the "Check Engine" light comes on, there is always a DTC (Diagnostic Trouble Code) stored in the ECM (Engine Control Module). You'll need an OBDII (On-Board-Diagnostics) scanner to retrieve any codes recorded/set in ECM. Once you do this and let us know what, if any codes are set, then we can go from there.

You need to replace the cmos battery in your computer. Theu are usually Cr2032 batteries which you should be able to pick up for about £1.

unplug your computer and open the case.
When you look at the motherboard you should be able to easily locate the cmos battery cliped onto the mobo.
Take the old battery out and insert the new one.
put the case back on and plug the pc into the mains again.
You will need to re-enter the date etc the next time you boot up, but the settings should be retained after that.

Ian

timing is set by the computer as long as you got the timing belt marks right it should run good.if not the cam timing is off and you will have to start over.

Hi ... I have the same problem ... I found this link but I haven't tried it out yet ...

http://www.emersonradio.com/dst_g2.htm

try starting your computer in safe mode and see if you can do anything productive there, like scanning for viruses or spyware. also check if you can do the following:
CTRL+ALT+DEL (open task manager)
goto Start>Run>Regedit (open registry editor)
goto Start>Control Panel>Display>Properties (change display settings)
right click on clock at tray and change the current time to correct settings

if you cannot do any of these activities, then your computer may probably been compromised by a virus or malware.