Question about Kenwood KDC-135 CD Player

1 Answer

Error code ( DCER )

The cd was play and it turned to this error......I power off an power on and this error apear always.......

Posted by on

  • judosan Jul 26, 2008

    Ok....you are right....thank´s..........

  • judosan Jul 26, 2008

    tHANK´S....DO YOU KNOW THE PART NUMBER......

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 132 Answers

The Amp chip has died, time for service

Posted on Jul 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code 22


"Error 22" on a Pioneer usually means an unsupported CD format. The disc you are trying to play is not supported or is very badly scratched so the player cannot determine the format.

Dec 19, 2013 | Pioneer Car Audio & Video

1 Answer

Error message on screen will not go away


Hello bigdsketch,

The "DCER" error is caused by one of the speaker wires shorted or grounded or a shorted voice coil. Remove the speaker wiring one at a time to determine which one is causing the error, then repair or replace the defective part.

You may need to press the reset button (small recessed button to the lower right of the volume control) after the problem is corrected.

Hope this helps.

Aug 15, 2009 | Kenwood KDC-135 CD Player

1 Answer

Kenwood KDC-138 Operation Problem


Here's the quote from the manual regarding "dcer": "The speaker wire has a short-circuit or touches the chassis of the vehicle and then the protection function is activated. Wire or insulate the speaker cable properly and press the reset button. If the "PROTECT/DCER" code does not disappear, consult your nearest service center "

I believe the manual can be downloaded from crutchfield .com after you go to the Kenwood KDC-138 page on their website. The reset button is either on the lower left of the face or, removing the face, on the lower left of the body. Hope this helps you.

Jul 24, 2008 | Kenwood KDC-138 FM / AM Receiver

1 Answer

"DCER" flashing....


That is a DC error.

What happened and why?
amp IC is fried, probably from overheating playing at very loud level. Maybe from a speaker going bad, maybe just random part failure

Is this fixable?
Yes

How do i fix it?
You must get the replacement part, take the radio apart, remove the solder from the amp ic, put new IC in and resolder connections. Put radio back together without forgetting anything you took apart. Also need to make sure the soldering is good, no solder bridges or anything like that (you wouldn't want to blow it up again right after replacing it)

How do i prevent this from happening again?
If it was caused by playing too loud for too long, don't turn volume up to point of hearning any distortion, that is clipping in the amp you hear and is very ******* amplifier ic.
If it happened from a speaker going bad you must replace the bad speaker.
If it was a random part failure there is not much you can do, you had some bad luck, thats all.

If you do not know how to remove solder and to solder very good, it is reccomended that you take it in for service, but it may not be worth it since this unit is not very exspensive. A shop may charge as much as $100 for this repair. part alone is about $30 or $40.

If you want to know the part number please reply and I will look it up for you, or you can get the generic number off the ic itself.

Jun 16, 2008 | Kenwood KDC-135 CD Player

1 Answer

Error code 6 & error code 4


hi try first to insert a clean up CD, and test your Cd player with an original CD, if the problem persist , your laser sense is defficient you have to go to fix it to a specialist.
hope this helps you
sserpentio

May 21, 2008 | Clarion DXZ438R CD Player

1 Answer

DCER error


the amp chip had died, service time

May 16, 2008 | Kenwood KDC-135 CD Player

1 Answer

DCER error (people spell it "ocer"


Problem is the internal amp chip, if it was a speaker problem or shory they flash Protect.

OCER oe DCER is the amp chip Part #KKZ10 REF# ic5

May 15, 2008 | Kenwood KDC-135 CD Player

1 Answer

DCER error


Every 1 of those i have gotten in service here the amp chip #KKZ10 REF# ic5

May 14, 2008 | Kenwood KDC-135 CD Player

4 Answers

LineOut


Yep. Take it to the nearest Sony Repair facility, usually when they say that there in an internal problem with the audio in from the laser to the audio ic


Don

Jan 02, 2008 | Sony CDX-R3000 CD Player

Not finding what you are looking for?
Kenwood KDC-135 CD Player Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...