Question about Kenmore 2.1 cu. ft. Portable Top Load Washer

3 Answers

Kenmore 44722 All of a sudden my washer is not working. All of the lights on the top control panel light up, but when I try to push them, nothing happens.

Posted by on

  • 2 more comments 
  • diy_ft Jul 26, 2008

    i have the same problem.. or close anyways. it seems to stop when it is suppose to spin. the machine stops completely and all the lights are lit. I can push the start button and that makes it restart, but then the same thing happens again on the first spin. It has been happening on and off for a while but unplugging it and replugging solved the problems before, but now, no can do.

  • nylaw Aug 05, 2008

    i have the same exact problem. Regardles of what cycle i put it in it fills with water agitates for a while then i hear a clicking sound and the machine drains. After draiing the water level light begins blinking and the machine stops. I can restart it but it just does the same thing again.

  • agmalo Sep 06, 2008

    I have the same problem. Does anybody have a solution?

  • rebeccaforak May 22, 2009

    the buttons are not responding when they are pushed and the washer isn't even 2 years old!!! I assume I need to contact an appliance repair place to replace the circuit board?

×

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I finally figured out what the problem is for my machine (by the way, mine is a Whirlpool compact top load LCE4332PQ1). it was simply that the machine could not drain adequately. after several uses, the flexible drain tubing out of the machine would get kind of stuck far inside the fixed drain pipe in the house and I guess the position of the tubing made it so that the water could not get sucked out or pushed out of the machine completely. A while back, while having the all-lights-lit issue, I wiggled the drain tubing and right away heard the machine finish draining and then it started spinning again properly. SoI rigged the flexible drain pipe so that it can't get stuck in this way anymore and I have not have the problem since.

The way i figured it out is by chasing down some troubleshooting tips on the manual and some tips pointed to a problem with drainage.

Posted on Dec 30, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

All I did was place a cloth between the washer and door to shut tightly. Started right up after.

Posted on Oct 17, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You need a new circuit board. Sorry, no way around it, the board needs replaced. You didn't mention how old your machine is.

Posted on Dec 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Dishwasher not working, no lights on control panel


If your good with electricity get a meter and with the unit unplugged check the resistance across the thermal switch... it should be 0.0 ohms(omega symbol) if a thermal switch is blown it will be open. and read unlimited ohms... I doubt if it is the thermal switch. Check first if you have voltage to the control board you should have lights on it. If no light then probably The door interlock switch has failed,, that is the first thing that I would suspect as I had that happen on one of my units... figure out how to bypass it or operate it.

Jan 18, 2014 | KitchenAid Dishwashers

1 Answer

My Ge Top load washer will not power up start button?,no lights.


Their is a fuse in the harness red wire that runs down from the control to the motor on the hydrowave washer. Hydrowave washer manual
Of course if yours isn't a hydrowave maybe you oughta post a model number. GE has several different styles.

Mar 09, 2013 | Washing Machines

1 Answer

My Kenmore Elite washer model 110.27062600 stopped working. All the front panel lights are flashing on and off for 7 times then pauses and starts blinking again. The machine will not do anything. No...


if this is an oasis model. Try pushing other buttons you should get a touch tone (beep) as a good response. if no sound you seem to have a interface problem. not a main ctrl.

Sep 19, 2017 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

He3 washer will not start. The lights on the


you probably broke the door switch and the machine thinks the door is open. little piece on top of the lock catch. need to change the door switch

Feb 05, 2010 | Kenmore Elite 45986 Front Load Washer

1 Answer

Control Locked


Locking controls
The Control Lock prevents unintended use of the washer. You
can also use the control lock feature to prevent unintended cycle
or option changes during a cycle. When CONTROL LOCKED is
lit, all buttons are disabled. You can lock the washer while it is
operating.

To lock the controls
Select and hold END OF CYCLE SIGNAL for 3 seconds.
The CONTROL LOCKED status light glows.

To unlock the controls
Select and hold END OF CYCLE SIGNAL for 3 seconds until the CONTROL LOCKED Status light turns off.

Oct 23, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Kenmore Elite won't start


The control panel (touch panel) is faulty - and must be replaced.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

May 27, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

My kenmore elite oasis washer will not turn on. I


its the power button its a common prob use a soldering iron and switch it with the load sinal button this happpens as the washer alallows moisture to get on the board as its not protected it will save u a ton of money and anyone can do it

Apr 26, 2009 | Kenmore Elite Oasis 27052 Top Load Washer

1 Answer

Washer stopped in the middle of the cycle


sounds like motor if nothing stuck between tubs or in pump ,check these first if ok you have bad timer

Nov 12, 2008 | Kenmore 22422 Top Load Washer

1 Answer

Kenmore top load washer model 110.44722401 won't start


The Machine does not know the lid is shut.... there is an arm connected to the lid... that arm runs just inside the the top cover and presses a button to signal the lid is down.. some where along the line the arm isnt pushing the button..take off the top cover and it should be an easy fix

Sep 06, 2008 | Washing Machines

1 Answer

Washer won't start


Open the control panel and check the door switch, mostly it's loose. You should hear click sound when the door is close if the switch is in working condition. Otherwise bend the contact metal a bit until it makes contact. Hope this helps.

Aug 27, 2008 | Kenmore 2.1 cu. ft. Portable Top Load...

Not finding what you are looking for?
Kenmore 2.1 cu. ft. Portable Top Load Washer Logo

1,400 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal De GO PATS

Level 3 Expert

2536 Answers

fordexpert

Level 3 Expert

5581 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...