Question about NAD C320 2-Channel Amplifier

1 Answer

Connecting sub with nad c320bee

Hi,
how can i connect my NAD C320BEE with SONODYNE ROAR2815 active SUB which has just 2 RCA input

Posted by on

  • B Carson May 11, 2010

    It would help if you typed a whole sentence to describe your problem.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 682 Answers

Pre out from nad---------to 2 rca input in sub.

Posted on Jul 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to connect an MP3 Player to NAD C320?


You will need a cable with headphone jack (for mp3) and RCA left/right to connect to your NAD 320. You can connect to CD or AUX in the back and then you will need to change the input with remote or with on board buttons to CD or AUX depending where you plugged it.

Jun 20, 2012 | NAD C320 2-Channel Amplifier

1 Answer

Nad c320bee keep over heating


Hello
Disconnect all speakers and switch ON the set without any input connected, and see whether it heats up. A moderate heat is permissable, but should not over heat. If it overheats without any load or input connected, the set need service. OK.

Jan 19, 2012 | NAD Audio Players & Recorders

1 Answer

How do I connect a Mirage Omni s-10 Sub Woofer and a Parasound Model 2100 Pre Amp to the NAD C372 Amplifier?


You DO realize the preamp is duplicating stuff in the Nad C372, right? This Preamps adds nothing but PHONO connectivity and control. That's why they're called "preamps".



Register and download the manual for free at retrevo.com

http://www.retrevo.com/support/NAD-C372-Amps-manual/id/8043dj592/t/2/

http://www.retrevo.com/support/Mirage-OMNI-S10-Subwoofers-manual/id/14438ag918/t/2/


Model 2100 Picture and article:

Use the Sub Out pair on the Preamp (joined by an RCA Y-cable) for the Sub Input on the sub (duh):

http://www.hometheaterhifi.com/preamplifiers/362-a-secrets-preamplifier-and-power-amplifier-review.html?showall=1

Run RCA from the Preamp Main Out to the C372 Aux In to hear any sources attached to the preamp.

Or, if you don't NEED the preamp because you don't have a turntable,ditch the preamp and connect the sub using the speaker outputs on the NADS, according to the manual.

Mar 08, 2011 | NAD C372 Amplifier

2 Answers

Hi, I have the Kenwood Subwoofer KS-201-HT, my question is how do I connect it to my receiver?


usually subs have outputs 4 ur monitors however if ur sub is active @ ur monitors are passive then you need 2 connect sub 2 ur tape loop with rca connections,usually you use the send signal from ur reciever which would norm connect to ur tape input , if the sub is passive then u connect direct to speaker output on amp then monitors to the sat connections on sub

Oct 12, 2010 | Kenwood SW36HT Subwoofer

2 Answers

Cannot get the sub woofer to work.


Now tell the NAD you have a subwoofer. Page 15, Figure 13, etc. and Page 18 - 19.

Mar 05, 2010 | NAD T770 Receiver

2 Answers

NAD C320 BEE - goes silent. Only yellow light.


Hi,
Just came accross your post accidentically, while reparing my own C320BEE. May be it 's too late for you now, but it could help others: I had the very same symptoms as you described and after a long search found out that the trouble was R45 in one of the 18V regulators. (R45: 33 ohms 1/2W fuse resistor, situated more or less half-way between the two "metal towers" on the main board. Replace by a somewhat stronger type 1W or so.
Likewise R46.)

Dec 23, 2009 | NAD C320 2-Channel Amplifier

1 Answer

No signal from sub connected to NAD T760 in test mode.


Try using front pre out to the sub from the receiver. the crossover is in the sub anyway. If this works change your settings on the receiver and test again. If sub is still inop, could be an internal issue with the sub amp. Does your sub amp have an on/auto/off switch or light? check that as well. Hope this helps, if you need further assistance, send a reply and I'll help some more

May 24, 2009 | NAD T760

1 Answer

Connect subwoofer etc to nad 3020I stereo amplifier


Hi Info
You can use a 2 x male RCA to RCA female adaptor lead(what you need to ask for)  like this one 4d0dcde.jpg

use it to jumper your pre-out/main in connection on the rear, and connect an RCA lead to the Female socket on the adaptor lead. That will get you going. You can get them most places that sell electronic bits and peices. I am happy to answer any questionsa you may have 
regards robotek

Mar 05, 2009 | NAD C320 2-Channel Amplifier

1 Answer

The right channel on my NAD intergrated amplifier C320Bee no longer works.


if you did test for your cable and speaker and you find it fine-your problem will be in output stage of your amp and needs aid of service center.

Jun 11, 2008 | NAD C320 2-Channel Amplifier

Not finding what you are looking for?
NAD C320 2-Channel Amplifier Logo

Related Topics:

737 people viewed this question

Ask a Question

Usually answered in minutes!

Top NAD Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

4706 Answers

The Knight
The Knight

Level 3 Expert

71117 Answers

krisefisher

Level 1 Expert

2 Answers

Are you a NAD Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...