Question about Audio & Video Receivers

1 Answer

The channel select button on my Peavey Transtube/Delta Blues footswitch won't work. When plugged into my Bandit 112, only the effects button was working. The pedal is brand new.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 682 Answers

Please try to apply a lubricant contact cleaner on select button and press it many times(you can get contact cleaner from radio shack near you)

Posted on Jul 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a lexicon mpx100 dual channel processor and a spirit powered mixer. could you tell me how to connect it to the mixer and does it need a stereo footswitch regards lawrence


Footswitch is just an option for activating MPX. There are a couple ways to connect, but easiest is to run cables from AUX outputs to MPX then return cables from MPX to 2 open channels, using them to apply effects.

Apr 01, 2011 | Audio & Video Receivers

1 Answer

Hello how doi adjust the left and right balance for the left and right channel level


The only 'balance' is to adjust the channels relative to each other with the test tones.

http://www.retrevo.com/support/Pioneer-VSX-24TX-Receivers-manual/id/386ag014/t/2/

Page 29.

The "Effect/Channel Select" button on the Remote (left of the Menu button), will let you change the level to any channels while listening to a program. Page 22

"EFFECT/CH SEL +/- buttons (See p.38)

EFFECT : Use these buttons to increase or decrease

the amount of effect applied in a DSP or Advanced

Theater mode. When the amount of effect is

increased in a DSP/Advanced Theater mode the

characteristics of that mode become stronger and

more noticeable. The scale ranges from 10-90 with 70

as the default setting. First turn on the DSP/

Advanced Theater you want (by pressing the DSP/

Advanced Theater button until you get the mode) and

then increase or decrease the amount of effect.

CH SEL : You may want to adjust the channels when

listening to some sound sources. Use this button to

select the channel you want to adjust.

+/- : Use these buttons to select the amount of effect
in a sound mode and to adjust the channel"



Jan 16, 2011 | Pioneer VSX-24TX Receiver

1 Answer

The footswitch for bugera 6262 valve amp seems to have a logic problem. The clean channel leaves 'lead and reverb' leds lit on footswitch, pressing 'lead' lights the crunch channel on the amp... and reverb...


Hi ! Check and make shure that the cord conections between the pc board on the backplate of the amp to the logic board are firmly pushed in there slots.
Good luck , Stefan from Sweden

Aug 18, 2008 | Audio & Video Receivers

1 Answer

Peavey 1200 Amplifier


Some of the outputs transistors is bad hence causing a bridge in circuit,thats why the fuse is blowing.Check all the outputs transistors on both channels,rectifiers and zena diodes these are the possible causes of circuit bridge when they are faulty.The fan works on AC thats why it is not affected even when the fuse is blown.Please if you have anymore challenge please send me a mail on mikewee4wee@yahoo.com

Aug 14, 2008 | Audio & Video Receivers

3 Answers

I have a peavey pro-fex 2 preamp/FX ver 1.3 controller and when powereing up, get DSP interface error. Do you know what this means or how to fix it?


Your Profex likely has a dead NiCD battery. You are getting this error because this battery maintains your personal effect settings on an SRAM chip that requires constant power to "live". You can try reinitializing the SRAM on your unit by doing the following:

1. Power off your Profex.
2. Press and Hold the "PLAY" and "GLOBAL" buttons while powering the unit on.
3. You should see a message on the display that reads "MEMORY INITIALIZED". Afterwards the Profex should act normal.
4. If your internal battery is getting low or is already dead, it is going to start leaking (if it hasn't already). YOU NEED TO GET THAT BATTERY CHANGED NOW!!!!! If enough battery acid leaks onto the circuit board, it will ruin your Profex forever.

Aug 03, 2008 | Audio & Video Receivers

2 Answers

Re: Peavey KB100 75 watt keyboard amplifier. Dear Sir, After having plugged into the 'PRE EQ PATCH' the main 3 inputs/channels are no longer working. I looked in the operating guide and...


The pre-eq patch connector is a 3 -wire connector designed as both an input and output in one connector. With a plug in there that only utilizes the output (send), you are not sending any signal to the amp section. That appears as no output. Take out the cable and the amp should be restored to original function. What you need to use that function is called an "insert" cable. This has a stereo 1/4" plug at the end for the "pre eq patch" side and 2 standard 1/4" plugs at the other end. One is for input into an effects box and the other is for the output from that efects box.

Hope this helps,
Dan

Jul 29, 2008 | Audio & Video Receivers

3 Answers

Peavey bandit 112 just stopped working


Fishfool67,
 If it is like the one I just fixed, the sound had just disappeared gradually when playing. To fix this one first and foremost unplug the unit. Remove the two top side rear bumpers, the 2 screws on the upper back metal ledge, you can feel them if you run your hand along this lip and locate, then remove the 2 wires connected to the speaker, ( just connector clips). Remove the power plug clip(one screw) then the 4 top side screws, I like to hold tray up with one hand and unscrew with the other. once these screws are all the way out the tray should drop down a bit. Just slide to the rear and rest it on the lower part of the cabinet. The return 1/4" jack is the dirty one that needs addressed but why not do all of the jacks while we are here. You will need a contact cleaner solvent. I use one designed to be used on printed circuit boards. You should be able to find some at your local electronics store. The cleaner should leave no residue after it has evaporated, check the cleaner you have and make sure it is the correct stuff. Next we will spray all of the 1/4" jacks, just spray enough to coat them good, let dry and repeat. them reassemble the amp and plug and play. Don't forget to reattach the speakers. This should fix your problem. 
TR 

Jul 20, 2008 | Audio & Video Receivers

1 Answer

PEAVEY TRANSTUBE AUDITION 110. PLUG UNIT IN POWERS UP . SITS THERE AND HUMS LOUDLY. SPEAKER WORKS. plug guitar in can hear it faintly, push lead chanel button in , hum gets super loud. HUM IS IN PROPORTION...


There should be an 8 pin IC close to the input jack that will be marked 4558 or 4560. This is an Op-amp Ic that is the most likely cause of the problem. Replace that IC and report the results here.
Dan

May 27, 2008 | Audio & Video Receivers

1 Answer

I have peavey 212 heritage guitar amp footswitch plug broke. I have new one but i need wire diagram please include colors and speaker conection.Thank U very much


Call the Peavey Customer Service line (number available @ the Peavey site) and get the parts department to email you a schematics on the amp... it has the footswitch wiring on it. And it's free to do this.

Apr 27, 2008 | Audio & Video Receivers

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68323 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...