Question about Projection Televisions

1 Answer

Pacific tv model will only turn on using the remote from standby, can i change so ut turns on from the power?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,712 Answers

Looks like a faulty power button on the TV..or bad circuitry..would recommend taking it in for servicing first..

Posted on Jul 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Panasonic tx 26lxd70


make this test for r.control use the digital camer or cell. When you hit any key you must see the LED ON, otherwise you must open the r.control for to clean da48b13b-b3c2-4350-aea2-883224ce8383.jpg the keypads from dirty, corrosion, etc, use the contact cleaner. tight the spring contacts batteries with plier for better contacts. and use alkaline batteries.

God bles you

Nov 04, 2013 | Projection Televisions

1 Answer

Lcdx37whd88


Sounds like your power supply capacitors have failed. Google for Z1234TV and see if you can locate a power supply capacitor repair kit for your model.

Mar 31, 2012 | Projection Televisions

1 Answer

I have a KP-57WV7000 that will not turn on. I got


try to turn the tv on using the sony remote and this sequence of buttons push display 5 volume up then power if the tv comes on change ic8002 on the power supply if it doesnt try replacing anyway this is a common issue with sony tv's

Jan 24, 2010 | Sony KP-57WV700 57" Rear Projection HDTV

1 Answer

Turn off after a few hours


If the TV turn itself off then perform the following steps:

(i) Check if the Sleep timer is activated.

(ii) Check if the Parental Guide prohibits viewing during that time and/or limits amount of viewing time per day.

(iii) Check the batteries on your remote, low battery power may cause random signals from the remote.

(iv) Disconnect all the cables from the TV then reconnect them after a few hours.

(v) Ensure the power cord from the TV is directly connected to a functional wall outlet.

(vi) You may also try resetting the TV to the original factory settings by pressing the Reset button on the remote control supplied with the TV when in Menu.

The following is the information indicated by the blinking patter of the standby/timer lamp on the TV:

2 times : Power does not come on.
Load on power line shorted.

3 times : The TV has entered standby mode.

4 times : Has entered standby state after
horizontal raster.
Vertical deflection pulse is
stopped.
Power line is shorted, or
power supply is stopped.

5 times: No raster is generated.
CRT Cathode current detection
reference pulse output is small.

6 times: No picture

9 times : No sound

Furthermore, the TV is equipped with a self-diagnosis function that you can use to determine whether the issue is related to any hardware malfunctioning. Perform the step given below to run self diagnosis:

Quickly press the remote command button in the following order from the standby state.

Display -------> Channel 5 ---------> Volume -(minus) --------> Power ON.

If the Self Diagnosis display numeral "1" for any parameters then a fault has been detected and service will be required.



wish u good luck!!!!!!!!!!

Sep 17, 2009 | Sony KP-65WS500 65" Rear Projection...

1 Answer

Can't turn on


When you turn the MAIN off you are killing all power to the set---Some advice---If you Google the model number of this set with the word problem after it you should find what I have seen a lot in these sets: they develop bad solder connections on the power supply printed circuit board---usually the board is about 18 inches tall and 12 inches wide--A number of sites online offer to have you ship them the board and they will resolder it for you.
I have repaired about 12 of these with this problem in the last 2 years---The board has to be removed(there are quite a few plugs that need to be labeled and removed and lots of screws that secure the board in place.)

Maybe not a job for a do it yourself person but the soldering (if it is your problem) will take about 45 minutes(including removal and installing board back).

Like most modern sets this set uses lead free solder and it is soldered(the boards) in a wave or one step process---over time from heat and expansion some connections may crack or even break loose----I would look at the POWER SUPPLY board(follow the power cord as it goes right to it)

If you have any questions or need help please contact me here.

I do this here for free so if this information has helped you take a minute and give me a vote here.

SD TECH

Sep 06, 2009 | Pioneer SD-533HD5 53" Rear Projection HDTV

2 Answers

I want to find the Sky remote code for this Tv.


Just got an LG 42LH2000 and code 0206 works

May 16, 2009 | LG Projection Televisions

1 Answer

My Matsui TV is a fairly old model and it does not have the buttons where you change the volume etc. My remote control has stopped working therefore I cannot turn my TV on. I have bought a universal remote...


matsui tv's are usually clones of another make set so you might be able to trace another remote ..try rs components for an original replacement.try switching on using the station up button...farr64

Apr 29, 2009 | Projection Televisions

1 Answer

TV won't turn on after cable outage


No your set would not be like the HD52W19 model ,your model number is on back of tv year,chassis & Model # being 10 yrs old ptk195 model------- older Rca ptk169 these sets are 16yrs old.My guess without hands on chassis Bad Flyback Transfomer.

Dec 02, 2008 | RCA D52W19 52" Rear Projection Television

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61037 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...