Question about Dacor Epicure ERD36 Dual Fuel (Electric and Gas) Kitchen Range

1 Answer

Dacor rsd305 Hello Experts, I did an oven clean with my Dacor and now it won't heat up again. I press bake and set the temp for 350 or so. The display starts at 135 and stays there. No heat. It reads 135 pre heat. I turned the breaker on and off with no change. Any suggestions? thanks

Posted by on

  • byronthe1 Jan 28, 2009

    Same problem. the bottom element does not glow but the temp on screen will get up to about 290 when you turn the oven off and then on again to display the present temp. The bottom element never glows. there was a flash in the oven before this started and there is a burn spot on the lower element. another solution elsewhere pointed to the temp sensor or the ERC?
    byron

×

1 Answer

Yes, you need to open the panel (in the center of the front of the oven when you open the door on the top) and press the reset button, there is a site that gives step by step instructions, but i can no longer find it

Posted on Aug 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My dacor microwave convection oven won't turn or heat but but the exhaust, time etc. works.


I found the answer on other posts on this website and it saved me $500! I had the same problem with my Dacor Model ECD2278 double oven. After I ran the self cleaning the top oven would not come on and the lower oven ran almost double the temp that was set. To fix: disconnect power to the oven at the circuit breaker. Open the oven door. You'll see the grille/grate/steel cover in front of the door latch mechanism, and it should have about 4 screws holding it in place. Remove the screws then remove the grille cover. On my model the tiny red reset button was on the right side on top of a black plastic round piece which is about 1" in diameter. Press the little button down til it clicks.

Oct 25, 2012 | Dacor ECS127 Epicure Stainless Steel...

1 Answer

Dacro Wall oven (electric) does not heat past 345 degrees on bake or convection bake but broiler works and bottom oven works fine (for bake, convection bake and broil).


it could be the oven temp sensor rod located near the top of the inside of the oven,or possibly the bake element has a hot spot on the element and can no longer pass enough current thru this spot to correctly heat to your settings a hot spot on the element will look discolored in this area

Jul 28, 2012 | Dacor Ovens

1 Answer

I press the bake button, i choose temp Ie:350 degrees, wait until goes up to temp, next thing you know, it shows 350 but the food is not cooking. press cancel, press bake and 350, temp starts to climb from...


More information is required make model, display type LED, or blue neon red light goes out when on temp, without more info cannot help.
johnf1

May 17, 2011 | Ovens

1 Answer

Bottom element is not heating to temp an shuts off during heat up - without error code showing in the display. IE. - Press Bake, 350 degrees defaults on screen; Press Start. YOu hear the Click as it...


Hello & Welcome to FixYa

This indicates an open/shorted oven temperature sensor and to solve this problem the sensor needs replacement. If you wan to be sure before replacing the sensor then you can test it with a voltmeter for around 1100ohms....if it reads more then this then it needs replacement however, if the reading is around or less then 1100ohms then it is the control board that needs replacement. Please get back to me if you have any other questions.


Kevin

Mar 05, 2011 | GE JTP15 Electric Single Oven

1 Answer

My upper oven/ convection function on my dacor ecs230b will not heat


Bake and convection bake settings both use the bottom bake element to heat. It would be unusual for bake to work without conv. bake working. You also have pure convection which uses a different element surrounding the conv. fan on the back of the unit. If you press a feature and nothing happens it's the touch pad. If it comes on then turns back off it's probably the ERC (clock). If it comes on and wont heat only in pure conv. possibly an upper relay board or element problem.

Sep 22, 2009 | Dacor ECS230 Epicure Electric Double Oven

2 Answers

My dacor oven model ECS130SBK is very slow to heat. Sometimes reaching the desired temp. after a long wait. Sometimes it never gets there.


I found the bottom element was not getting any power by using a volt/ohmmeter and a test method described elsewhere. (Shut off power, hold down COOK TIME while turning on power. then within 30 seconds press each mode you want to test and only that element/fan/etc will turn on. Cancels by itself after 30 sec.)


I traced the wire back to the relay (wire checked good) and there was no power getting through the relay although it clicked. Removed the relay board to replace it and found a cold solder joint on the "out" terminal with obvious past arcing carbon. Cleaned and soldered the pin and the oven now works normally.
WHY THE SLOW TO HEAT? The oven turns on all the elements to preheat faster and when it reaches your set temp it beeps and now only turns on the element you selected to maintain the temperature. (Bake or Convection) Our malfunctioning ovens would then cool since the element is not working properly and it must go back into preheat and keep cycling.
BY THE WAY- Don't ever use 4 hours on self clean it kills the boards and/or display. I also put a house fan in front of the oven and blow it into the lower grill to take away some of the heat on the two boards. Learned the hard way!

Jun 08, 2009 | Dacor ECS130 Epicure Electric Single Oven

1 Answer

Dacor rsd305


Once you replace the oven control again....never use self clean on any oven....unless you want to replace parts.
Before you replace the control...look inside the control panel for a resettable thermal fuse.

Mar 10, 2009 | Dacor Epicure ERD30 Dual Fuel (Electric...

1 Answer

Our Dacor Millennia wall oven will not heat


There is a manual reset button behind the vent under the touch pad. Turn off the power. Open the door. Remove the vent. Behind the latch is a two wire switch. press the red button on it until it clicks. reassemble and turn on power. It over heated when the power went off by stopping the cooling fan.

Mar 04, 2009 | Dacor MCS130SS Millennia Electric Single...

2 Answers

OVEN WILL NOT COME UP TO TEMPERATURE


Hello,

You can calibrate the oven on this model. Press the bake button, adjust the bake temperature up to 550 degrees and then press and hold the bake button until a 0 displays. Now you can adjust the oven temperature up or down to match the display.

Here is a repair manual link that you can use to download frigidaire repair manuals. The one for 30 inch freestanding ranges will have the section on calibrating the oven's electronic control.

Thanks

Jan 09, 2009 | Kenmore 40494 / 40495 / 40499 Electric...

Not finding what you are looking for?
Dacor Epicure ERD36 Dual Fuel (Electric and Gas) Kitchen Range Logo

541 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dacor Kitchen Ranges Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

Jaime Hernandez

Level 3 Expert

2296 Answers

Are you a Dacor Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...