Question about Car Speakers & Subwoofers

1 Answer

I need a wiring harness or a picture of the wiring harness for a pyle PLTSN74

Posted by on

  • hattoos Apr 21, 2009

    i need the wiring plug for pyle pltsn74

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I NEED TO FIND A WIRE HARNESS FOR A PYLE IN THE DASH DVD PLAYER PLTSN74
JONES-RAY@sbcglobal.net

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to wire my 4 ohm DVC subs to my Pyle 3000 watt home receiver amp


No you don't. You'll fry the amp. You need a low frequency processor to strip the mid and hi frequencies out of the signal applied to the subs or you'll have a full frequency sub that will sound cruddy. If your amp outputs 8 ohms the you'll have to wire 2 speakers in series or poof goes the amp. If the amp is only 16 ohms then you're out of luck unless you have 2 more speakers to connect in series to the 2 you aleady have.

Feb 19, 2015 | Pyle Car Speakers & Subwoofers

1 Answer

Pyle powered speaker (PPHP123MU) How do you replace the fuse. System completely shut off in middle of use. No power at all. Thanks for any help.


Amp or head unit ? Amp power lead fuse should be located in a holder close to the car battery ,the amp itself will have a fuse as well should be near the terminals where the power and speaker leads are located on the unit , head unit will have a fuse on the wiring harness and a fuse from the main power supply fuse panel in the car.

Nov 06, 2014 | Car Speakers & Subwoofers

1 Answer

Pyle PLTAB8 Car Component System, Lights will not turn off. Help


Sounds like he did not wire a remote line from your radio to the amplifier, if he put a 12v from the battery to the amp and the remote spot on the amp then it will not turn off, you will need to either wore a toggle switch to the remote so you can turn it off manually or check the back of your radio for a remote line or splice a remote line from the accessory power supply on your radio so the amp will turn on when the radio is on

Feb 06, 2012 | Pyle PLTAB8 Car Component System

1 Answer

I am installing a Pyle PLMR87WB stereo into a Pyle PLMRCW3 Water resistant stereo housing. I am soldering the connectors and shrink wrapping them. Do I need to connect the memory wire. I do not want to run...


OK, time to go into cheat mode. You can always install a toggle switch to that wire. The only features I see you losing are that the time will be incorrect on the clock and it might not save your preset radio stations. All other functions are basic. Might I suggest a lighted toggle switch, this will help to remind you to turn it off.

Happy Wiring

Aug 13, 2011 | Pyle Car Speakers & Subwoofers

1 Answer

I have a pyle 12"


Hi there,

I am afraid in order to make use of your sub, you will need to buy an amplifier and a cabling kit to run it. You could run it straight from the headunit from one of the main channels but it would need a crossover so it wasn't fed any sounds which it couldn't cope with (high frequencies, they require very fast movement of the speaker cone, your sub wouldn't be able to do it)

Here is a link to a downloadable copy of headunit manul.

Hope this helps

May 09, 2011 | Pyle Car Speakers & Subwoofers

1 Answer

How to install, since it doesn't come with instructions.


Unless your speakers / boxes are specific for your car, there will not be any installation instructions beyond generalized that may include a wiring diagram, a chart to show how much volume your speaker box needs (minimum and optimum), power handling, etc.

Search for your model / part numbers at Pyle Car Audio and see what information is available there.

Sep 18, 2010 | Pyle Car Speakers & Subwoofers

1 Answer

I have a pyle blue wave 12inch 800w subwoofer for a car hook up?


that just means it is dual channel.

if you have a stereo amp just run the left wire to one terminal and the right wire to the other terminal.

if your amp is mono run the wires to the first terminal and then from there to the second set of terminals.

PLEASE NOTE that by doing that you are bridging the speaker if the speaker was 4ohms to start with you just dropped it to 2 ohms so make sure your amp can handle that.

Dec 24, 2009 | Pyle 12" Molded Blue Cone High Power...

1 Answer

How do wire up a Pyle dual 4 ohm sub woofer speaker, the PLCHW15 3600 watts. Do you wire up both sides or do you wire up one side of the connections?


Hello shannon_e_ha,

Both voice coils need to be connected to the amp.

If you wire the coils parallel (both +'s and both -'s together and then to the amp), the final load will be 2 ohms. If you wire the coils in series (one + to the other - and the remaining + and - to the amp), the load will be 8 ohms. If your amp is 2 ohm stable, use the parallel wiring. If it is only stable at 4 ohms or greater, use the series wiring.

Hope this helps.

Oct 31, 2009 | Pyle PLCHW15 Car Speaker

1 Answer

Need install help on Pyle PWLB12D speakers


you will need to take old ones out and cut to stock connector off and wire the new one in

May 02, 2009 | Car Speakers & Subwoofers

Not finding what you are looking for?
Car Speakers & Subwoofers Logo

Related Topics:

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Speakers & Subwoofers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Car Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...