Question about Toshiba (GM1030) for E-Studio 200L Print Server

1 Answer

Network will not initialize

Network cable was unplugged and when I plugged it back in , I get "Network Initializing" on screen

Posted by on

  • 1 more comment 
  • mfinseth Jul 21, 2008

    This is for the Toshiba E studio 200L

  • larango Dec 04, 2008

    I have the same problem on estudio 4511. Have turned it off and unplug several times and still has not fixed the problem

  • Am Naqvi
    Am Naqvi Apr 02, 2009

    Hi, I have tried and shut down and restarted the eStudio 450 several times and the problem persists

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Mentor:

    An expert who has written 3 tips or uploaded 2 video tips.

  • Expert
  • 115 Answers

You need to shut the machine down, turn off power and restart it... it should go through the Network Initializing after it has connection with the network, this screen should go away..

Posted on Oct 24, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

49.ff04 service error


Try changing the network cable. Connect the other end to another port of the ethernet switch.

If it doesn't work, remove the Network cable and using the printer console reset printer to factory default so that printer use DHCP.

Connect back network cable and try again.

Some people powered down and remove & cleaned the RAM edges. Removed and reset the EIO network interface.

Dec 25, 2013 | HP LaserJet 4100 Laser Printer - Plain...

4 Answers

Connecting this print server


try unplugging both and then plug in the router,let it reboot, then plug in the other and let them find each other. if that doesn't work let me know.

Oct 02, 2008 | D-Link RangeBooster G DPR-1260 (DPR1260)...

1 Answer

Printer connected but not printing


Hello,
If your printer has a network port you should be using the network adapter.
Otherwise you want to make sure you connect the printer with a USB cable to the appropriate port on the D-Link.
Once the USB cable is connected you should be able to add the printer from your computer as a shared printer.
You will not normally see any activity lights on your router for the USB connection because it does not send or receive information the same way the LAN cables will.
I do recommend a LAN cable though as it works much better with routers. If your printer does not have one I would look into getting a network printer.
Thanks,
Pat

May 12, 2010 | D-Link DP 300U (DP-300U) Print Server

1 Answer

We have urgently to stop the packages send to jetdirekt_500x. pleae hlep


Do you mean "packets"? Not to be a smart-***, but you can unplug the network cable, then wait for the printing device (you computer) to error out, and then cancel the print job. Then plug the print server back in.

Dec 18, 2009 | HP JetDirect 500X Print Server

1 Answer

Computer can's see Print Server in Add Printer Wizard The WGPS606 installation -- part 1 -- seemed to go fine. It sees our wireless network, we assigned it an IP address, it sees the printer connected to...


Make sure the printer has been connected locally first and that the print drivers have been installed. This should then allow you to add the printer via the set up.

Regards gaz

Sep 28, 2009 | NetGear WGPS606 (WGPS606NAR) Print Server

2 Answers

How do i reset my hp jetdirect 170x


Unplug the power to the HP Jetdirect 170x, press and hold the test button. while pressing the test button, plug the power cord back into the device and continue holding the test button for another 5 seconds.

This will reset the device.

http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00758101/c00758101.pdf
page 5-64

Aug 11, 2009 | HP Jetdirect 170x Print Server

1 Answer

HP750c Plus, with Jetdirect j2552a or j4100n not working.


Here's a few troubleshooting steps that should help you out.

1. Are you getting a link light? If not, check the cable and the switch - if these are OK then you have a bad JetDirect.

2. Print a test sheet from the 750 and check the IP configuration. Be sure that you have an IP address that is on the same subnet as the computer you want to print from. If not, then you either need to configure an appropriate static IP or configure DHCP for the MIO and make sure it is working.

3. Once you have the IP worked out, try to ping the MIO from your PC. You can also try to connect to the MIO using the embedded web server if the firmware is recent enough. If either of these work then you should be in good shape. Try to re-install and see if it works.

One last thing, if you are printing directly to the plotter from the client computer without using a print server then one part of the setup is non-intuitive. When you are asked if the printer is local or network, you have to select "local" even though this is clearly not the case. Then when you get to choose a port, create a new TCP port.

Good luck and if the above doesn't help, post an update and we'll take it from there.

Jul 16, 2009 | HP Jetdirect 170x Print Server

11 Answers

Level One Print Server not serving


Hi Mr Giles,

If you click on your Network icon in the bottom right hand corner of your Vista Desktop, and click Network and Sharing Center, is Printer sharing enabled?

Chris (ziraffa)

Jan 18, 2009 | Levelone ServCon WPS-9122 (WPS9122) Print...

1 Answer

The 3 LEDs remain green permanently, even when cables are disconnected


Unplug it over night. try it again tomorrow. If it still shows all green its fried. It there a reset button anywhere on it? Try holding it down(if there is) while plugging it in. Keep the reset depressed for 30 seconds or so. Otherwise no bueno. Let me know what happens. Good Luck, Tim

Mar 22, 2007 | Trendware TRENDnet TE100-P1U Print Server

6 Answers

How do I reset access password?


Thanks. I actually found out that it had never been configured - here is the standard factory access info: All Oki network printing devices support configuration changes via a standard web browser such as Internet Explorer or Netscape Navigator. When applying a configuration change to a device the user is prompted for a user name and password. The following details should be entered: User Name: root Password: last six digits of the MAC address* *You can find the MAC address on the network summary web page or by printing off a menu from the printer.

Nov 22, 2006 | Okilan 8100e Print Server

Not finding what you are looking for?
Print Servers Logo

Related Topics:

444 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toshiba Print Servers Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

old marine
old marine

Level 3 Expert

1463 Answers

Cindy Wells

Level 3 Expert

4755 Answers

Are you a Toshiba Print Server Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...