Question about Haier Heating & Cooling

1 Answer

Hi the compressor on my split air conditioning unit will not cut in .the indoor unit runs and the compressor light on the indoor unit lights up?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 95 Answers

If the system is appearing to turn on, but no compressor, Check the capasitor on the condensor unit. If you open the service panel, you can test the compressor by pushing in the contact switch. If you push the switch and all comes on, Replace the thermostat after checking to make sure the thermostat wires are not cut or disconnected. The capasitor usually looks like it is swelling if it has gone bad

Posted on Jul 21, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my sanyo model KHS2472 has a red light blinking in heat mode and a green in cooling mode, does not work in either mode makes a gurgling sound when it tries to run?


Hi,
The red light indicates it's either heating or in defrost mode
Check the outdoor unit if the compressor is running - the large pipe on the outdoor unit should be hot on heating or cool to touch on cooling
When in heating mode - the indoor fan will not start until the indoor coil is warm enough
If the reversing valve that changes from heating to cooling is faulty then you may encounter the same symptoms too
Probably need a Refrig Tech to have a look at it?
Good luck

Jan 07, 2016 | Sanyo 24KS72 Split System Air Conditioner

1 Answer

3 split units run from one compressor one is not cooling


If there is 3 indoor units from one condensing unit
(6 pipes at outdoor unit) this is classed as a multi unit

All units will run correctly as long as they all require same mode, cooling or heating, if one unit decides to heat it will shut down until master unit decides to heat then it will start, for each unit to individually heat and cool there would have to be 3 pipes to each indoor,

Dec 19, 2015 | Fujitsu 9RLS 9000 BTU Split System Air...

1 Answer

The unit either encountered a brown out or a surge which burned up the board for the condenser. It had black marks on the board and the indoor unit was flashing. Replaced the board and the unit is still...


After replacing the burned condenser board, check also the entire condensing unit if still ok ( compressor and fan motor). If the light inside the indoor unit is still flashing, the timer is still not giving signal for the compressor to start. Adjust temperature and wait for 3-5 minutes. It light continue flashing, there is something wrong with the indoor unit control.

Sep 02, 2011 | Sanyo Split System Air Conditioner

1 Answer

E 7


Multi Splits and Multi V = indoor unit is set to run in a different mode from the master indoor unit. Set ALL indoor units to cooling or ALL to heating to clear.
Splits = Compressor Over Current (CT2), Check loose wiring/condenser coil for clean

Jan 10, 2011 | AmcorAire UCHW-H24AF2 Split System Air...

3 Answers

Aircon runs for a few minutes then shuts down and timer light flashes


when we start the AC indoor working and out door unit compressor working but fan motor not working and indoor timer light blinking

Dec 16, 2010 | Mitsubishi MSZ-A24NA Split System Air...

1 Answer

LG Art Cool, 2 splits. Error code CH7


Multi Splits and Multi V = indoor unit is set to run in a different mode from the master indoor unit. Set ALL indoor units to cooling or ALL to heating to clear.
Splits = Compressor Over Current (CT2)

Jul 09, 2010 | LG Art Cool LA121CNP wall/window Air...

1 Answer

When we turn on our split AC, outside unit is not turning ON


The blinking light is because the unit is waiting for the outdoor unit to come on. If in heating mode, the indoor fan will not run before enough pressure and therefore heat has built up. You should check that the indoor air return sensor is not faulty and therefore preventing the outdoor unit from coming on.

Nov 15, 2009 | Amcor NanoMax A12000E Portable Air...

1 Answer

Fujitsu Air Conditioning split unit Model


Your compressor is seized up. shut down unit and let compressor cool down, it may start again but probably needs to be replaced.... sorry for the bad news,

Nov 10, 2009 | Fujitsu 24C1 Air Conditioner

1 Answer

Outdoor unit does not start. indoor unit fan does run.


by the sound of it the relay in the outdoor section is bad

May 31, 2009 | Heating & Cooling

Not finding what you are looking for?
Heating & Cooling Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Heating & Cooling Experts

Tom Chichester

Level 3 Expert

39229 Answers

Matt
Matt

Level 1 Expert

52 Answers

Vincent Schnittert
Vincent Schnittert

Level 1 Expert

38 Answers

Are you a Haier Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...