Hello, my Frigidaire GLTF1670A Front Load Washer timer is not advancing. It will go for a little bit then stuck and runs and runs until I advance it myself. What part needs to be replaced? The timer washer mallor or could it be something simpler?

Good Morning kvojik, thanks for your post!

From my understanding your Frigidaire front load washer is getting stuck between the drain and spin cycle. I noticed that you have replaced many components within your washer and continue to experience this issue. I would not advise to manually advance any part of the washer because this could cause issues within your washer. It could be a potential issue with the motor. At this point you may want to reach out to a technician for proper diagnosis and repair. This will help you to avoid any further part purchases. -Matt

Must be a problem with your timer switch.

Hello - This particular issue can be caused by quite a few reasons. Washer could be experiencing a communication error from the main control board, faulty door lock assembly or the timer itself is not operating correctly. Since you hear a humming noise, either the drainage hose/pump is clogged and needs to be cleaned or could possibly have another issue with the door lock assembly or pressure switch. You can also press and hold the start/pause and cancel button together at the same time for approximately 30 seconds to display an error code on the LED. What error code does it display? However, I would suggest contacting a professional to accurately diagnose the washer.

Hello there:
If your cycle does not complete or The cycle doesn't advance When the cycle should advance, it's probably the timer or a cold-water supply problem: It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer. It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. than check the cold water supply line and the filter

The cycle doesn't advance When the cycle doesn't advance, it's probably the timer or a cold-water supply problem:

• It's the timer, if your washing machine fills with water and begins agitating, but the timer never advances--or if the washer is in a spin cycle and the timer won't advance. Then you need to replace the timer.



• It may be a cold-water supply problem, if the washing machine fills with water, agitates, drains, and spins, but then doesn't fill with rinse water. See There's no cold water.

1. Changing the front boot
   
2. Cycle Not Advancing or Timer Stalling Symptoms Update
   
3. Motor won't run helps
   
4. New fault codes for the electronic controlled Frigidaire built front load washers 
   
5. Noise problems or rust on the clothes
   
6. Need help naming that part?  Washers - various models  Interactive
   
7. Operation and installation tips
   
8. Won't drain water helps
   
9. Odor problems with your tumble style washing machine  
   
10. How to remove and replace the drum gasket on the Frigidaire - Kenmore ( 417.###### ) Front Load Washer with notes on tub bearing replacement and inner drum replacement
    
11. Washing one item in a front load washer
    
12. Some door switch helps 
    

Reason? There shouldn't be one. Seems you're extraordinarily unlucky with timers. Mine's 10yo, never broke. The timer is a standalone part, it's not dependent on any other parts for its longevity. So there can't be any other parts in the washer 'killing' it.

Are you handling it gently? Turn it slowly when setting, don't whip it around.

I bought the frigidaire affinity washer. It was quiet until it began the spin cycle, then it sounded like a jet taking off and began to bounce. Come to find out we set it up improperly. You must remove all shipping bolts on the back of the machine and make sure it is level. Ta Da!! it now runs perfectly quiet with little vibration.

did you check the filter? If the filter is plugged in the least bit it won't allow machine to spin at high speeds

if its a top loader check for timer/timer module fault.front loader check carbon brushes in motor