MESSAGE PT630 BIOS VI.94 MEM 4608 KB WHAT SHOULD I PRESS TO PUT IT ON SCAN MODE? (READY) THANK YOU

Hi Jon.

Go into the BIOS confuguration by pressing the F2 key as the laptop starts up and set the BIOS to its default configuration. Save the changes by pressing the F10 key or save in the BIOS menu. The computer will restart so see if that has made any difference.
If you still get the same IDE #0 error then the hard drive is ready for failing. A replacement hard drive will not cost much at all.
Seeing as you have only spent $20 on the laptop in the first place you have got yourself a bargain there. Spend a liitle money on a new drive and OS then you could have a fully working laptop.




Regards.

to store a fcy press BAND to go to your fcy range ie 118.000 airband
dial your fcy ie 127.900(shanwick ocean area control) press and hold V/M for 1 sec, small numbers now blink, dial the memory slot you wish to store into ie 001 then press V/M again for 1sec and this will store 127.900 into mem slot 001. make a list:-
mem number / fcy / mode(am - fm) / station / bank
to prog a fcy into a "bank", press V/M for 1sec - blinking mem numbers - dial mem number ie 001(127.900) press MODE - "bank" flashes past-
-- -- -- -- 001 shows, turn dial to show A-00 this is the first "bank", pressing BAND scrolls through all the alpha "banks" - choose one.. ie A-00 (for airband..) press V/M this puts mem 001 into "bank" A mem slot 00, there are 100 slots in each letter 00 to 99. do this to any fcy you want to scan as a group.
to scan a bank press V/M - small numbers appear -
press BAND to scroll through any "banks" you have created ie A B C D etc (only banks with fcys in will display), press MODE -"bank"- press MODE again and you will start scanning just that "bank" of mem slots.
MODE starts and stops the scan... each letter holds 100 mem slots.. happy scanning!!!

The number of characters read is defined in your application and the width of the printed bar code. Also the width of the laser or ccd. One program to develop applications JobGen Plus de Unitech.
Roberto Martinez

try this....
create an "airshow" bank to scan just the airshow fcys.
press V/M for 1sec -blinking mem numbers- dial a known mem that has an airshow fcy stored in it ie 025 (127.875) press MODE "bank" will flash past..
-- -- -- -- A-00 shows up ( I use this bank for airshows) press V/M, this puts mem 025 (127.875) into "bank" A mem slot 00, each letter holds 100 mem slots , put all your aishow fcys in here and when you scan bank A you will only scan the airshow fcys and not the entire airband!!
to scan a bank...
press V/M - small numbers show- press BAND this will diplay your bank letters, just select A## then press MODE for 1sec -"bank"- press MODE again and you will start scanning just A for airshows...
press MODE to start and stop the scan.. happy scanning! ps Southport was not as good this year as last year although it was good to see the vulcan again!!

That message which your scanner is displaying is the normal and correct mode in stdby, there is no problem with it.
If the scanner says "bad command" is because you are pressing the "enter" (ENT) key without any command selected before.

Bye.

Sometimes viruses can trigger slow start ups. Try running your virus scan. also, you should make sure that your memory is working correctly. When you have a memory stick that has failed, its hard to tell if you have over 2 gigs of mem installed but, when you start it up, it will struggle during the process.

anne834: Press and hold the CMD botton.

Roberto Martinez
[email protected]

Hello, Do you still need the solution? You can warm reset and exit the kermit mode, and then the download ur data using PTComm.

What program are you trying to replicate? Is it a third party application? What error you received on the PT630 screen when u run the program.