Question about D-Link DCS-G900 Network Camera

1 Answer

Cannot see camera on network. The link light just keeps flasing.

I recently purchased this camera. When I follow the instructions, it is supposed to show up on a list when I run the wizard. What I noticed is that the power led is on constant, but the LAN led just flashes wherther it is connected to a LAN or not. Is there anyway else to access the camera in order to set it up?

Posted by on

  • cdred1854 Aug 06, 2008

    Ive been given a dlink dcs g900 i camera but have no software for it, is it possable to configure this without the software you would get with it or do i need to find drivers etc ive connected the camera with a standard cat 5 cable and tryed to ping it but get nothing any help would be great?


1 Answer

If you follow the instructions the guru sent you, you will learn how to set up your camera. After reading the comments I couldn't stop laughing. You probably won't find anyone to help you here after seeing how you rate good answers. Your best bet is to just hire a private investigator.

Posted on Jul 29, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have 2 sony snc-rz30N cameras that recently can not be seen on the network. They are all pluged in however the network light on the camera does not come on.

Check the 12 Volt AC adapters for correct levels. Connect one computer ONLY to the cameras on the Ethernet and see if you can communicate. Verify you get composite video from the BNC jack. Check your router.

Jan 25, 2011 | Sony SNC-RZ30N Network Camera

1 Answer

What does each button stand for


i suppose you are asking about the remote control buttons...

Arrows:Use the Up, Down, Left and Right arrows to tilt/
navigate the camera lens.
Home: Returns the camera lens to the home position set
by the user.
Auto-Patrol: Enables the Auto-Patrol function.
Auto-Pan: Pans the camera one full cycle.

Center :Centers the camera lens.
Stop : Stops the movement of the camera during pan.

Jul 15, 2010 | D-Link DCS-5300 Network Camera

1 Answer

How to set up for email alerts


please follow the instructions.

1.install the IP surveillance
2.Go to 'my network places'
start---->control panel---->my network places
3.You will see your device

4.Double click it you wil get a window like this...

5.Click on the configration button. wil get this page...

7.please select 'Advanced'(this is on the top)-------->Network(this on the left hand side)
8.In this page you have an option called as'1st recipient email adress'.please enter your adress and click on 'apply'

Now you can recieve the video clips. thanx

Jul 15, 2010 | D-Link DCS-3220 Network Camera

2 Answers

Hi, I'm having trouble with changing the IP address on the SecCam

you can try this ,here i got the details about the dns query ,ip to domain ,domain to ip can get more about the ipadress......

Jul 13, 2010 | D-Link DCS-5300 Network Camera

1 Answer

Im not have driver for my cam hama helpppp


Here is a driver which might help you install the camera.

After you click on the above link make sure you click on regular download button and then follow onscreen instructions to download and install the software.

Thank you for using fixya.

Jun 14, 2010 | Hama Concord 1-20 Numbered Polypropylene...

1 Answer

My d link DCS5220 cannot be detected on the installation wizard

The first time the camera is installed, you must make sure it is connected directly to the router switch via network cables. This will ensure that it is seen in the install wizard.

Once wireless networking has been configured, save and reboot the camera for changes to remain in place.

NOTE: Please rate our help to keep this free service online.

Jan 09, 2010 | D-Link DCS-5220 Network Camera

1 Answer

How to set Static local IP Address for D-link DCS 5220 IP Camera? Am using Linksys WRTG54 Router, with SSID & WPA. I had set the D-Link DCS wireless to use the same SSID and WPA, but once I plug out...

To set a static IP on the camera, do the following:

1. Chose an IP address for the camera that is outside your normal DHCP range but within your network subnet.
For example, if your router uses DHCP and gives out addresses in the range of up to, you should chose an IP address beyond that (e.g.
2. Login to your camera's current IP address and go to Setup -> Network setup
3. Turn off DHCP and type in the IP address that you chose into the configuration.
4. Restart your camera.

The above should fix your Static IP address question.

With regards to your Wireless question, you should make sure of the following:
1. Your router is set to broadcast its SSID
2. Your router is setup to use WPA (not WPA2)
3. Your AES password in the camera config is the same as that as the routers

Hope this helps

Nov 24, 2009 | D-Link DCS-5220 Network Camera

2 Answers

My DLink 5300 G internet camera suddenly says "No Signal."

  1. Remove the Java update and roll it back to the previous state.
  2. If it does not resolve the issue, reset the camera.
  3. Lightly insert a paper clip or a similar sized object into the reset hole on the back of the camera, press lightly and then release the button.
  4. The LED on the front of the camera will begin blinking red and green.
  5. When the LED stops the blinking, the reset has complete.
  6. If the issue is still present, restore the camera to factory settings.
  7. Insert the paperclip or other tool and press on the button continuously.
  8. Wait for the LED on the front of the camera to blink red and green and hold the button through two cycles of blinking (about 5-7 seconds.)
  9. Withdraw the tool after the second cycle of the LED blinking and factory restore has been completed.
  10. Run the installation wizard. If you don't have the installation CD, go to the manufacturer's website and download the software.

Nov 10, 2009 | D-Link DCS-5300 Network Camera

1 Answer

When i switch to wireless mode, camera stays in;privacy mode

Unfortunately the electronic operating instructions are not available from the support website and have to be purchased from Panasonic.
I think it will be a case of re-setting the camera to factory settings and re-program the webcam again

Aug 25, 2009 | Panasonic BL-C131 Network Camera

Not finding what you are looking for?
D-Link DCS-G900 Network Camera Logo

Related Topics:

387 people viewed this question

Ask a Question

Usually answered in minutes!

Top D-Link Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18344 Answers


Level 3 Expert

4332 Answers

Are you a D-Link Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides