Question about NetGear WGR614 Wireless Router
For that particular Netgear router, if you have NOT changed the
password, the default username is "admin" and the default password is
"password" (or "1234" if it is an older router).
If this doesn't work, you will have to do a reset of the router which will put its settings back to the factory defaults. On the back of the router, you will find a recessed reset button that you will have to press for about 10 seconds until the TEST light blinks (use a straightened paper clip).
If you do not have the manuals that came with your router, this website has the setup and user manuals for your device, but you will first have to determine the version by looking at the model # on the bottom of the router:
Hope this helps!
Posted on Jul 21, 2008
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Password recovery isn't really possible. Pushing the rest button in the back for a few seconds will reset the router to factory defaults. You will need to reset all the wireless security and such so best to do this with a pc connected directly to it. Default IP for it if you have changed it is 192.168.2.1.
Posted on Mar 25, 2009
SOURCE: password change
After logging in the web configguration page you should see a menu like this:
Click Wireless -> Interface to open the configuration page.
You should see an interface like this:
If you have any more questions or this didn't work for you, just come back here and leave a comment - I'm happy to help.
Posted on May 20, 2009
This is not a difficult task, but if it is done incorrectly, your router will need to be reset. So, let's go ahead and get a long, thin pin, or sewing needle,or something that will reach into the recessed reset button hole, because we may need it a few times.
I too have a belkin wireless router, so I know a little about them. However, I dont know your exact model or firmware/software programming, so a true "step by step" is not possible from me. Contact Belkin for operator assistance. Here are some General things you will need to do.
1. Reset the router. Go ahead and do that now. that way, we have a clean slate. Press the reset button and allow the router to restart.
2. Make sure the Modem is connected to the INTERNET port on the router. You should see 5 ports on the router, 1 2 3 4 are ONLY FOR COMPUTERS. if it has a number do not put anything on it unless its a computer, or xbox or playstation game console. The MODEM, the DSL, or w/e will NEVER go to ports 1 2 3 or 4. Now, make sure that your MAIN computer is HARD WIRED to PORT 1 on the router. You DO NOT EVER make wireless router adjustments over a wireless connection. You must hard wire to the router.
3. LOG IN to the router. The router has a built in website that allows you to operate it. on a belkin router, that website is located at the Default Gateway address. (ok, you probably dont know what that means, but thats ok, we can still do this). MOST belkins have a default gateway address of 192.168.2.1. So, you will open your internet explorer and go to the ADDRESS BAR. There, you will type http://192.168.2.1 and press GO. You SHOULD see a page that says Belkin.
4. BY DEFAULT there is no username or password. so if you are asked to login, leave them blank and hit submit.
5. this is where it can get hairy, but, its nothing the reset button cannot fix. You will be looking for a few things First thing to do is click login, of course, so you can log in. remember, its default, so its blank.
6. Now that youre logged in, look for WIRELESS and click there. If you are using wireless machines, make sure wireless is ENABLED. It should be, by default, but, lets take a look and make sure, just to be safe.
7. Next, were gonna set the SSID to your last name, (or your dogs name or your nickname or favorite place). The SSID is default to Belkin, but if 10 ppl around you ALL have belkin routers, you'd have no way of knowing which one is yours, So, the SSID boradcasts a unique name to identify YOUR network. Changing the word Belkin to "Scoobydoo" would mean that you would be the Scoobydoo network, and anytime anyone is in range of your router, they would see "scoobydoo" as a site. You also want to ENABLE Essid broadcast, and unless you have an older wireless B card, set to Wireless G only. (g is more secure). Everything else, leave at the current setting.
8. Now we are going to SECURE your wireless so that when people see "scoobydoo" they wont be able to JOIN it, unless they have your KEY. Click Security. We are going to create a key. With Wireless G you can use a 26 character key, which is a set of HEXIDECIMAL characters. HEX is 0-9 and A-F. No letter higher than F will occur in Hex. So, click WEP (wpa is usually more secure, but I prefer WEP). Choose WEP and Choose 128 bit encryption. Next, use a passphrase, (this will generate a key for you). Say you put "shaggy" as the passphrase. Based on that word, a 26 character key would be generated. Now, This is important, WRITE THAT KEY DOWN EXACTLY AS ITS SHOWN. Without that key, no one can access your router on wireless. Also, dont forget to press "Apply Changes". Once you apply those changes, all your wireless connections will be lost. You will now have to go to each wireless computer, and apply the key to each one so they can access the router.
Posted on Jul 21, 2009
go to the router's setup page and setup the wireless encryption there. to do this better contact the router manufacturer to get the IP of the router
Posted on Sep 15, 2009
Tips for a great answer:
Sep 17, 2012 | Linksys Wireless-G WRT54G Router
wireless network is comprised of a wireless router, a computer (or
other wireless-enabled devices), a high-speed modem, and a subscription
to an Internet Service Provider (ISP). Netgear is a popular
manufacturer of wireless networking hardware that allows users to set
up a secured wireless network. In order to prevent unauthorized users
from logging onto your wireless network to gain access the Internet,
and in order to protect the data you transmit and receive online, you
should change your wireless router's security settings to create a
secured wireless network.
1 Install the router. To install a Netgear wireless router, use an Ethernet cable to connect the router to the cable/DSL modem and use another Ethernet cable to connect the router to your computer. Make sure all of these devices are powered off as you connect them. Once connected, turn on the cable/DSL modem, the router, then the computer, in that order. Allow at least two minutes to pass after turning on each device to give the devices time to recognize one another
2 Log in to the router. Open a web browser and type in the router's address to load the router's settings page. The router's address can be found in the user guide or setup CD that came with your router, or you can download a user guide from Netgear's technical support page (see Resources). Most Netgear routers use one of the following addresses: http://192.168.1.1; http://www.routerlogin.net; or http://www.routerlogin.com. Press "Enter" or click "Go" in your web browser after you have entered the address.
3 Enter the router's username and password. A prompt will appear on the screen when you enter your router's address, requiring you to enter a username and password before you can access the router's settings page. The default username for Netgear routers is "username" and the password is "password." Because the textboxes are case-sensitive, you must enter both of these using all lowercase letters. Press "Enter" to log in to the router and begin changing its security settings.
4 Open the security settings menu. The router's home page has multiple links for changing settings. Find and click the "Security Settings" link to change the router's security settings.
5 Change the SSID, choose an encryption setting and create a password. The default name (or "SSID") of your wireless network will be "NETGEAR." Enter a new, memorable name for your wireless network to help detract would-be hackers from trying to access your router, as most novice computer users with unsecure networks do not know how to change the default network name or institute any other security features. Newer Netgear routers offer WPA or WPA-PSK encryption to secure your network, both of which provide high levels of security. Select either of these. encryption types and create a unique password. This will require all users to enter the password before they can log in to your wireless network. It is important that you create a complex password that has several characters, including numbers. Once you have created a password, click "Confirm Password" to save it. To exit the security settings menu and log off of the router, click "Save" or "Apply" to save the changes you made, then click "Logout" to exit the route
Things You'll Need
* Netgear wireless router
* High-speed Internet service provider (e.g., Comcast, AT&T, Insight)
* Cable/DSL modem
* 2 Ethernet cables
* Web browser
* Router address
* Router's username and password
Good Luck : ) ....
Oct 14, 2011 | NetGear WGR614 Wireless Router
Dec 12, 2010 | Linksys Computers & Internet
Oct 14, 2010 | Computers & Internet
Sep 10, 2010 | Computers & Internet
Aug 05, 2010 | Linksys WRT160N Wireless Router
Jul 13, 2010 | CP International WBR-3406TX Wireless...
Jun 07, 2010 | U.S. Robotics USRobotics USR5461 Wireless...
May 16, 2010 | SMC Barricade 7004VWBR Wireless Router
Feb 09, 2010 | Linksys Wireless-G WRT54G Router
179 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: