Question about Garland AF-5025 Deep Fryer

1 Answer

The fryer was working normal. Then the temperature light went out and the fyer is not coming on whe I flip the off an on switch

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 254 Answers

The first thing you need to check for is a high temperature limit cutout switch. It will be located near the gas valve but on the right side it wil have a cover that will snap open. it is about the size of 4" X 1 1/2". Once you get it open puch the button in you shoul dhere a click. When you hear the click you are reset. Once you turn the fryer back on use a temp probe or a type K thermocouple w/ a meter to check temp. if it starts over riding temp shut the unit off and replace the t-stat and the t/l cutout switch.

Thanks

Posted on Aug 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace the gas valve on pitco fyer model 35c+s


Either go to Pitco's website and look for cutsheets/parts info or call the company directly... They can walk you through it at no charge... Susan Restaurant Equipment Outlet, Cinc, OH
reocincinnati@yahoo.com

Aug 25, 2011 | Pitco Frialator 35CS Deep Fryer

1 Answer

Have a fryer that i have a problem keeping lit. the reset button when oushed keeps clicking once you get it to stop the fyer will lught however only stays lit a few minutes. not sure if its that swutch or...


Unless the fryer is running at 400 degrees or higher its that switch that is bad. That is a high limit and should not trip off unless the fryer gets close to the flash point of cooking oil which is in excess of 400 degrees for most oils. If I'm not mistaken the high limit is set to trip at 450. It's also a good idea to check the temperature of the oil when its working properly. It should run at 350 and its common to see the flames go off at about 360 and then come on again around 340 to maintain an average of 350. A bad high limit is a common problem.

Aug 06, 2011 | Pitco Frialator 35CS Deep Fryer

2 Answers

Fyer will not shut off after reaching temp reset button comes on


Hi there.
Your thermostat may be bad, it does not cut-off on temperature setting that's why temperature continues to rise tripping the hi limit switch.Try replacing the thermostat.
Visit http://www.pitco.com for parts inquiries and owner's manual download.
Regards.

Jun 06, 2011 | Pitco Frialator SG18S Deep Fryer

1 Answer

Fryer overflows often, turned thermostat down from 350 to approx 340 but food does not cook then. could the thermostat be bad? 10 degrees should not make that much difference.


Does the fryer have a" temperature reached light"? If so switch the fryer on and with the thermostat dial starting at its lowest setting increase the temperature setting in small increments. When the light indicates temperature reached, increase the thermostat dial temperature. Continue until maximum temperature reached.

If (starting from cold) the temerature reached light only shows when high up on the thermostats temperature scale, then unfortunately the thermostat needs replacing.

Hope this helps.

Mar 04, 2011 | Dean D50G-C Deep Fryer

1 Answer

Can not get fryer to turn on. when you flip the switch to the on position, the high limit light flashes and go back off emediatly, and no power comes back on. i can here a click in the board behind the...


The High Limit is a self resetting thermostat that acually works like an oven control. If the fryer is too hot it will cut off the gas burner valve voltage:
OEM PN is 00-854453
Original PN VUL854453

Source 1
http://www.3wire.com/webstore/parts/PartSearchResults.aspx?searchText=Switch+High+Limit&mfrCode=VULCAN
$98.50
Source 2 Must log in.. new account
http://www.a1service.com/vulcan/vulcanlimit.htm
$90.20

The 854453 number comes up often in the part search for the high limit.
The high limit contacts can be checked and reading the NO and NC terminals. This control / switch is normally closed until opened by heat at 450 Deg F.

Thanks for Choosing FixYa,

Kelly

Sep 28, 2010 | Vulcan GRD45 Deep Fryer

1 Answer

Fryer wont fire up


Check the continuity, flip the switch on and off using an ohmmeter, if the switch is ok, check the thermal fuse inside.(you have to open the unit) replace whatever is defective

Jun 28, 2009 | Pitco Frialator SG14 Deep Fryer

2 Answers

Hobart deep fryer, light pilot heats to temp then all goes out?


You will need someone who is qualified in commercial gas appliance repair to fix this.
Liabilities would render this out of reach for anyone else.

Mar 29, 2009 | Hobart 1H50D Deep Fryer

1 Answer

Just bought wells fyer model # F-67


3 phase is VERY DANGEROUS, contact an electrician,

Jan 26, 2009 | Wells F-67 21167 Deep Fryer

Not finding what you are looking for?
Garland AF-5025 Deep Fryer Logo

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garland Deep Fryers Experts

starztruck4u

Level 2 Expert

77 Answers

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Treefrog15
Treefrog15

Level 2 Expert

126 Answers

Are you a Garland Deep Fryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...