Question about Washing Machines

1 Answer

WASHER WON`T FILL FULLY WITHOUT RE OPENING TOPLID SEVERAL TIMES?

HI, RECENTLY BOUGHT 2ND HAND WASHER,A WHIRLPOOL ULTIMATE CARE 2 GSC9455. TOP LOADER.INSTALLED AS PER INSTRUCTIONS, EXCEPT I HAVE NO HOT FEED, WAS TOLD AS LONG AS I CONNECT THE HOT FEED PIPE AND CLAMP THE PIPE TO STOP LEAKAGE THE MACHINE WILL RUN FINE.(DONE) HOWEVER ELSE WHERE I WAS ADVISED I NEEDED TO INSTALL A "Y" CONNECTOR TO SUPPLY THE HOT FEED WITH COLD WATER AS WELL. ? (NOT DONE).ANY WAY, THE MACHINE PART FILLS WITH COLD THEN STOPS. IF YOU OPEN THE LID AND THEN SHUT AGAIN IT FILLS A BIT MORE AND STOPS. AFTER ABOUT FOUR TIMES IT STARTS TO WORK AND APPEARS TO RUN FINE. ANY IDEAS? PLEASE

Posted by on

  • NJR69 Jul 20, 2008

    THANKS FOR ADVICE.WILL TRY,THEN GET BACK ON OUTCOME

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 93 Answers

Water valve should be a single unit consisting of a hot and cold solinoid assembly. This whole valve assembly should be replaced.

Posted on Jul 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a whirlpool ultimate care II washer. It stopped in the middle of a load, full of water, and now it won't do anything. It won't drain, fill, move, or make any noises.


You will need to check the capacitor on the machine. It can be tested with a capacitance meter the easiest. It can be tested with a resistance meter, but this will tell you if the capacitor is shorted or open. It will not tell you the capacitive value if the component has drifted out of tolerance. You put the meter across the terminals and watch the display for counting up to infinity. This will occur quickly and disappear very quickly. Now reverse the leads on the terminals, (reverse the polarity). The same thing should happen, but a bit more pronounced. It will once again rise very quickly and go to an infinite reading. This tells you that the capacitor isn't shorted or open internally. Here is the capacitor to order if you should find it bad.

Nov 28, 2012 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

How do I repair my Whirlpool Ultimate Care 2 LSQ9549L Top Loader Washer?


check the motor coupling,if the coupling is broken you'll hear the motor run but the agitiator won't move and no spin,the coupling connects the motor to the transmission.watch this video
http://www.youtube.com/watch?v=9K1KHEogf3c

May 30, 2012 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool ultimate care II stops after filling


Hi, could be faulty timer, faulty water level switch, faulty start capacitor for motor, or faulty motor. always put clothes in machine before starting. you can empty machine by lowering drain hose to flow level.

Aug 02, 2009 | Whirlpool Ultimate Care II GSW9650LW Top...

1 Answer

Washer will not fill up


IS YOUR DRAIN HOSE AT LEAST TO THE TOP OF THE MACHINE - OTHERWISE IT MAY RUN OUT OR SYPHON OUT/

Jul 26, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

I need to find out how old is my Whirlpool Washer Ultimate Care 2


The copyright on the owners manual is 2003.

Here is a -->link<-- to download the manual if you would like.

Please take the time to give this solution a fix ya rating.

clarkco


Feb 09, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

My washer starts to run then trips the house breaker


Probably severe arcing on motor commutator due to worn out carbon brushes

Jan 24, 2009 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool ultimate care 2 water wont stop filling...over flowing everywhere.


Your level switch hose has come loose.first open the display panel to check in back of water level switch,and look for a hose that is not attached to the back of it.

Jun 07, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Whirlpool Ultimate care II Washer Agitator not turning


replace the dogs in the top portion of the agaitator, the agaitator top comes off and you will see the four dogs part number is 285707 about 3-5 dollars

Apr 16, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

63242 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...