Question about Krups Aroma Control 229 Coffee Maker

1 Answer

Where to buy replacement parts?

Need the small rubber hoses that connect to the heating element.

Posted by on

  • Anonymous May 06, 2009

    I also need the same hoses



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Link to part:

Part number is Krups 0694911 Tube
$2.99 each + shipping, special order - 2-6 weeks to ship. Had to go through their customer service to get exploded parts diagram with part number, but if I can save a perfectly good coffee maker from the scrapheap for $6 + shipping, it'll be worth the effort and the wait.

Posted on Sep 12, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Leaks as it brews

If it's leaking water out the bottom, then it is a problem with the short hose that attaches the water reservior to the heating element. These rubber hoses have to handle the high temperature of the heating pad and water pump, so they often crack and leak after four or five years of use. They can be replaced with parts from another old model if you have a handyman close by, or buying another one is the option.

Dec 14, 2013 | Black & Decker CM1050B


How to Replace Heating Element from a Maytag Dryer?

The procedure is as follows:--- 1) First of all unplug the dryer from electric outlet for safety reasons.
2) Locate the vent hose on the rear of the dryer and disconnect this hose from dryer unit.
3) The hose is mostly fixed in a metal clamp and the metal clamp is fixed by the screw. Loosen the screw and remove the clamp and remove the hose.
4) The heating element is located in the cabinet.
5) In some models the cabinet is located at the rear of the dryer. And in some model its located in the front of the dryer.
6) Locate the heating element cabinet and remove the screws holding the cabinet.
7) You will see the heating element now. There are wires connecting on the sides of the heating element terminals. The wires are connected by removable connector.
8) Remove the connector carefully from heating element with the help of needle nose plier.
9) After the wires are removed from heating element’s terminals. Remove the screws holding the heating element.
10) The heating will have to be moved a bit to come out easily. Before removing the heating element out. Please note down the position of old heating element. So while placing the new heating element you don’t face any problem.
11) Remove the old heating element and insert the new heating element.
12) Connect all the wires as it were connected before.
13) Refit all the parts which you removed while removing the old heating element in reverse method. Take care you don’t miss any part fitting.
This will help. Thanks.

on Mar 20, 2010 | Dryers

1 Answer

I need two rubber hoses that supply water to the heating element. Where can I acquire these?

try a auto parts store they should have what you need for a fraction of the cost of parts at a service/ repair center. Mike

Dec 07, 2012 | Cuisinart DCC-1200 Coffee Maker

1 Answer

This water heater has two elements, correct?? Well how do you get them out?

The first thing to do is shut off power supply to the heater. Then while water is still on hook up garden hose to drain valve on bottom of heater. Place hose to floor drain or some other location for safe drainage. Open drain valve and if it starts draining at a good rate then shut water supply valve off to heater. You will want to open hot side of closest faucet to prevent vacumn which will slow or stop draining. After heater is done draining shut off drain valve and faucet . Remove the cover plates on top and bottpm of heater. Usually four small screws. Locate heating elements and disconnect wiring,label if you need to for reinstallation. There are two kinds of heating elements,one is held in place with 4 hex head bolts,and the other is screwed in. If yours has the bolts carefully remove to avoid breaking bolts.Then just pull out to remove To reinstall there will be a new rubber gasket with element, fit it in place and insert element back in heater. Reconnect wires. If there are no bolts apparent then the element screws into heater. You will need a pipe wrench or large wrench to remove the element. The same thing with this element is that it should have a new rubber gasket. Put gasket in place and wrap threads with 5 to 6 wraps of teflon tape. Install element and tighten snugly. Connect wires,refill with water and check for leaks. If no leaks then turn power back on. Put cover plates back on and you're done. I hope this helps you. Thanks

Nov 19, 2010 | Audiovox Richmond 6EM30-2 30-Gallon 6-Year...

3 Answers

The coffe maker is leakingout the bottom when the

Same problem here. The hose has a one way valve in it as well. I slid the hose part way off the reservoir connection and used the extra length to make up for the portion I cut off at the cut (you may have to move the on one way vlave further down the hose). This was intended as temporary fix while mywife bought a new coffeemaker. The new coffeemaker has been itting here six months as my temporary fix continues to hold.

Jul 04, 2010 | Cuisinart DGB-600 Coffee Maker

2 Answers

My Kenmore electric dryer runs but no heat ....

Before I wish you luck i want you to review all of the possible reasons for your problem

If your dryer doesn't heat, check these:

Power from the house
Heating element
Thermal fuse
Power from the house Check to see whether there's power getting to the dryer. Is it plugged in? Check for blown fuses or tripped circuit breakers--your dryer uses two fuses or circuit breakers. The dryer could tumble but not heat if only one of the two fuses is blown. If you have circuit breakers, one of the two circuit breakers can trip, even if the two for the dryer are connected.

Heating element Often a dryer heating element burns out, but doesn't trip the circuit breaker or blow a fuse. The heating element is simply a long coil of special wire. You can check it for continuity with an ohm meter. No continuity means the element is bad and you need to replace it--electric heating elements aren't repairable.

Thermal fuse On many dryers, there's a thermal fuse mounted to the exhaust duct inside the back cover panel. The fuse--which is about an inch long--is usually embedded in black resin and mounted in a white plastic housing. If the fuse has blown, you need to replace it. (You can't re-set it.)

Wiring A common problem is for the main wiring connection from the house, at the dryer, to burn and break its connection. Because the dryer can still tumble with partial power, the connection may be only partially defective. You may need to replace both the power cord to the dryer and the terminal block inside the dryer that the wire is attached to.

May 29, 2009 | Kenmore 62602 Electric Dryer

1 Answer

Dryer runs but no heat

There is a small white fuse held in by one screw on the back of the dryer near the outlet hose. If it is blown the dryer will not heat. It usually blows because of lint clogging the line somewhere so the entire dryer line has to be vaccuumed out with a shop vac. The fuse has two wires connected to it. You can check it with a voltmeter for continuity. This is the least expensive part to replace. Second part would be the electric heating element(electric dryers only) The timer is somewhat expensive to replace but easier than replacing the heat element .

Oct 04, 2017 | Dryers

1 Answer

Hobart LX30H Parts

Heating elements don't need to "look" clean to work proper. I would use a wire brush to remove the looser stuff, and ignore the rest. A thin scale layer is not a big deal for an element.

I'd stick with the rubber plugs. They work pretty good if you get them in all the way. New arms would be pretty expensive. Just buy a few extra plugs. And don't cut yourself installing them!!

May 08, 2008 | Hobart SR24-H Built-in Dishwasher

1 Answer

Looking for the part no.

the part you need is called the upper oven hi limit thermostat any appliance parts store can get it with your model number and any stove wire will do if you cant find it there then try here

Feb 11, 2008 | Maytag MER6772 Gemini Electric Kitchen...

2 Answers

Unit will not perk water

I've had one of these for several years and have replaced the water heating element several times. Abtec sells the entire heater element plus new rubber hoses as well as just the thermostat and fuse, which is what actually fails.

If you're handy with tools and small appliances and take your time you're in and out in 10 minutes. There is a small allen screw at the back of the unit and the same size allen at the top of the heating element. Make certain you don't lose the small plastic ball that acts as a check valve at the end of one of the hoses.

At $35 plus shipping for the element it's almost not worth the time and trouble since new units run about $50, but this is a nicely designed unit, not available any longer, other than the durability of the heating element.

Aug 22, 2007 | Black & Decker SpaceMaker ODC325 Coffee...

Not finding what you are looking for?
Krups Aroma Control 229 Coffee Maker Logo

418 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krups Coffee Makers & Espresso Machines Experts

Billy Mac

Level 2 Expert

83 Answers


Level 3 Expert

78010 Answers

Ross Keen

Level 3 Expert

1297 Answers

Are you a Krups Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides