Question about Sharp XR-10X Multimedia Projector

1 Answer

Projector shuts off sporadically

Thank you for responding to my post. I just realized I must have posted twice by mistake, and you read the shorter message. I copied my second post below which has more details. Thank you in advance for your advice and suggestions.
I have owned my sharp xr-10x for 2 1/2 years now, and for the most part, it has worked well. My current remaining lamp life is 76%. However, recently the projector lamp dims, then turns off at irregular intervals (10 mins-over an hr). The fan remains on and, after a couple of minutes, the lamp turns on again. The standby/on light remains on through this, and the lamp light blinks green while warming up again. I am afraid my lamp life has diminished due to the frequent shut-off and back on periods. Any suggestions?

Posted by on

  • eddienosbod Sep 17, 2008

    I have a SANYO Plv-z1 and it powers off after about 30 seconds of showing picture. The filter is clean and this evening I put in a brand new bulb. This is hugely disappointing and I'm not sure what on earth to do now. Any suggestions?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

Hello,

1. Pls check the airflow of the cooling of the projector, or just service the all unit.

2. As you told that the lamp life is 76%, Check the inner
reflector have shiny surface of dimmy, If not shiny, then replace
the lamp unit.

Enjoy

Viren

Posted on Jul 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vivitek Qumi Q2 reset ?


Unplug the power cord from projector
--> HOLD down (keep holding down) the right key on the keypad (top of the projector) and Insert the power cord back to the projector
--> The "Power" and "Ready" LED light should blink TWICE and unplug the cord from the projector (while still holding down the right key)
from facebook site

Jan 02, 2013 | Vivitek Qumi Q2 WXGA 3D Ready LED Pocket...

1 Answer

As all the posts on here I have the same problem. My panasonic pt-lb10u turns on, green light flashes, fan comes on. Then the green light turns red and the red lamp indicator light comes on. No light emits...


Hi,

If your projector won't fire up then you can't reset the lamp counter so that is not the problem.

The combination of LEDs you have given does not correspond to an error message. There should be two LEDs, one of which is the Lamp Indicator, and the other is the Temp Indicator.

It's possible that an overheating problem has caused this. Make sure the projector is in an area where the temprature is between 0 °C (32 °F) and 40 °C (104 °F) and the humidity is between 20% and 80% (with no condensation). It shopuld have unobstructed air flow around it.

Disconnect the power. Remove the lamp and place it aside. Clean the air filters, using a hoover, being careful not to damage the filter which is located on the underside at the front of the projector under a flap.

Carefully reinstall the lamp (when you say you replaced the lamp, did you buy a new PANASONIC lamp from a reputable source?) Try to fire up the projector. Note down any combination of LEDs if the projector doesn't work and post hem back here.



.

Feb 14, 2011 | Panasonic PT-LB10VU Multimedia Projector

2 Answers

We have two Dell 2400mp DLP projectors that will shut down randomly. The time that the projector is never the same.


I just got done talking with Dell, they told me to unplug everything from the projector, power source and all. Then Press and hold the power button down for 45 seconds. This will disapate the electricity from the capacitors. Plug everything back in, and test. Seem to wook for me!! Good Luck

Feb 04, 2010 | Dell 2400MP DLP Projector

1 Answer

I have a projector (SONY VPL-ES1) and the bulb stopped working. Took the bulb out, and not sure if it's blown or not. I checked online, to see if anyone else had similar problems, and sure enough they...


usually the projector powers and cools down. if you restart it it will open the cover, not projecting anything and after 10 seconds it will close again. this happens if the lamp is shortly before the end of the measured lifetime (no fixed hours) to protect the projector. usually if you take it out once or twice it will work for 1 or 2 more times but the bulb is very likely to explode (not destroying the projector but not good anyways)

Dec 30, 2008 | Sony VPL-ES1 Multimedia Projector

1 Answer

NEC LT240 has Power, Status & Lamp indicators lit & wont turn on!


If your bulb finally reaches it's end before you have the chance to replace it you unit will shut itself down and go into a permanent standby mode. Changing the bulb alone will not remedy the issue. The solution is quite simple but not posted in the manual or anywhere else that I could find for that matter! All that is required is to hold down the HELP button on your remote for 10 seconds while aiming at the infrared sensor on the unit. This will reset the units bulb timer and remove it from the standby mode.

Dec 10, 2008 | NEC LT 240K Multimedia Projector

2 Answers

I need a wirless driver for a mac computer


Hi again,

Seems that you posted twice. Pls, here is the link to your other post.

Cheers.

Feb 07, 2008 | Panasonic PT-LB60NTU Multimedia Projector

1 Answer

Dropped PROJECTOR and now it won't turn on.


I think this projector uses a color wheel. It's literally a wheel a transparent wheel divided into different pie shaped colored sections.

I am not an expert (or even close) on these proejctors, but I would guess that a fall like this would cause a mechanical problem and the wheel is a mechanical part. If it's not allowed to rotate properly it could be the problem.

If you're in a brave mood you might open it up and see if the wheel is able to spin freely.

Good luck.

Nov 19, 2007 | Sharp XR-10X Multimedia Projector

1 Answer

Dropped computer - it won't turn on


get it looked at and do it fast. Buy a different mount so this doesn't happen again. and don't hang the projector too low. It might need service

Nov 19, 2007 | Sharp XR-10X Multimedia Projector

2 Answers

LCD shutting off automatically


Hi there

Check if your blowerfan that cools the lamp - sits in front of Projector is running.

Nov 06, 2007 | BenQ PB2140 Multimedia Projector

Not finding what you are looking for?
Sharp XR-10X Multimedia Projector Logo

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sharp Multimedia Projectors Experts

Electro Med Services...
Electro Med Services...

Level 3 Expert

5601 Answers

kc5mgc

Level 1 Expert

8 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Sharp Multimedia Projector Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...