Question about Fisher Dryers

1 Answer

Fisher-Paykel electronic dryer. Since wallmounting, after pressing start it only does half a rev and beeps ! Reset etc didn't help. Any tips?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Sounds as if the air flow sensor is blocked or has failed since moving the unit

Posted on Jul 20, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fisher paykel smart drive 601


Hi just read your post.When the machine beeps a series of lights will light up on the wash progress line of lights. Staring from left to right the long wah is number 1 and the spin light is number 8 which lights sre on when the machine beeps, is it 2, 4 and 8 or 1, 3 and 7 etc.Please reply with this information and I sure I can help you. Regards LU

Jan 24, 2014 | Fisher and Paykel Fisher & Paykel Washer

1 Answer

Our dryer is just beeping twice when I press the start button and won't turn on. The model is ED56U and it is a front load dryer. Can you help?


Hello & Welcome to FixYa

The beeping sound usually comes when the circuit board which supplies power to the unit also known as the electronic control goes bad and needs replacement. You can also test the door switch before replacing the control, if the switch is fine then control replacement is recommended repair. Please get back to me if you have any other questions.

Kevin

Nov 28, 2010 | Fisher and Paykel Dryers

1 Answer

Fisher & Paykel Auto Sensor Dryer stops & beeps constantly


Hi emkboyce

my Fisher Paykel auto sensor dryer keeps stopping and beeping, i have to stop it and and re start.

I had the same problem. I took it off the wall and vacuumed up all the lint from everywhere including around the back and including taking off the back and vacuuming everything I could reach inside. I then used a damp cloth to get rid of the rest of the lint/dust.

I thought I was wasting my time but guess what, the problem has gone.

Good luck!

Sep 30, 2009 | Fisher and Paykel DEGX1 Electric Dryer

2 Answers

My fisher and paykel dryer ( mod# ED56 ) wont start, power is on


I had this same problem with my Dryer. It is making the few quick beeps because it thinks the door is still open. Near the bottom of the opening to the dryer there is a sensor switch that gets pushed in when you shut the door. Try holding the switch in with a knife or something and then start the dryer with the door open to check if that is the problem.
After i did this, i closed the door and my dryer started as normal.

Aug 11, 2009 | Fisher and Paykel DEGX1 Electric Dryer

1 Answer

Dryer tries to start - then stops and beeps PLEASE HELP


Check the exhaust hose. If the dryer isn't venting properly it will either stop or the heater will turn off and the clothes will remain wet. If the hose is not clogged check the wall vent tube.

Apr 29, 2009 | Fisher and Paykel Dryers

1 Answer

Dryer won't start. Pressing "Start" button just emits 4 beeps.


does the drum turn? if it doesnt you can assist it and see it that is problem, have to remove top and push it. that would be capacitor on motor or jumper the door closed switch and try to spin.

Apr 21, 2009 | Dryers

1 Answer

Hi I have a Fisher & Paykel Auto Sensing dryer model ED56... The dryer only works for about 10 seconds and then starts to beep..have I touched something I shouldnt have...turning it off and starting...


Hi,

Initially, try a reset; unplug from the mains for about half an hour. Thereafter, plug it in, press Power and restart.

If not corrective, verify that the lint filter is clean and that the Delay Start has not been engaged. Likewise pls check if your particular version/model has a reset switch at the rear of the unit. often, this would be a small pushbutton type. Press on it. try again.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.


Jul 25, 2008 | Dryers

1 Answer

Fisher & Paykel ED52 electronic tumble dryer. Since several power failures two days ago, when power button is activated & "start/paus" button pressed it beeps 4 times & won't work. I...


I found advice on the Fisher Paykel web site that suggested the problem could be the door lock. In fact the catch had not properly engaged & when I fixed that the dryer worked.

Jun 19, 2008 | Dryers

Not finding what you are looking for?
Dryers Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher Dryers Experts

Tim Whalen

Level 3 Expert

3069 Answers

paul
paul

Level 3 Expert

754 Answers

kev bush

Level 2 Expert

90 Answers

Are you a Fisher Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...