Question about Amana 3.2 cu. ft. Top-Load Washer

1 Answer

Very loud on spin cycle

The noise has gotten extremely loud during the spin cycle. Sounds like maybe bearings going bad.

Any ideas?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,028 Answers

Yes ..bearing on upper side of gearcase has gone bad probably from a water leak from tub seal

Posted on Jul 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer makes rumbling noise during spin cycle


You have to take the whole drum out and IT IS YOUR BEARING(s). Order all four of them

Oct 22, 2014 | Washing Machines

3 Answers

Loud noises during spin cycle. Drum is eating up. All springs and shocks appear to be ok


The water seal has worn out and water has gotten into the bearings. You need to call a service tech to have it repaired. It is not a cheap repair. Whirlpool has a repair that replaces the back half of outer tub and a new inner tub or basket one in the same. Another salution is replace the seal and bearings, still a lot of labor. go to utube and a guy does to an LG, but the the repair is about the same for a Duet

Aug 08, 2014 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Very loud rumbling noise during spinning


Most noises from a washing machine occur during the spin cycle. If you hear loud thumping during the spin, the load of clothes may have become unbalanced. Stop the washer and redistribute the clothes, then re-start it. Repeat these steps if necessary.This will solve your problem.

Sep 05, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

I have a top load Roper washer that won't spin.Any ideas?


That sounds like a bad drum bearing, check and eventually replace the drum bearing.

Dec 28, 2008 | Roper RAS8445KQ Top Load Washer

1 Answer

Loud noise during spin cycle.


If it sounds like a jet engine and gets louder the faster it spins you have bad bearings and that wont hurt anything. If your using pwder soap that is what made the bearings go out so switch to liquid and it shouldnt get much worse.

Nov 17, 2008 | Washing Machines

1 Answer

Maytag Washer HAV2558AWW loud noise during spin cycle


Your maytag is really an amana and the bearings are bad. Yes it does cost a lot. If i were you i would buy another washer. Get a whirlpool. (whirlpool now owns maytag)

Nov 16, 2008 | Maytag Atlantis MAV6000 Top Load Washer

1 Answer

My wash spins SO loudly


hiya
sounds like your drum bearings are in need of replacing.

hope this helps


please dont forget to rate the helpfulness of this reply, thanks kj

Aug 19, 2008 | Washing Machines

1 Answer

Loud Noise during spin cycle


I have a maytag that sounds the same way but washes and spins fine despite all the noise???

May 20, 2008 | Amana NAV2335A Top Load Washer

1 Answer

Noisy Spin Cycle


frigidaire frontloader infamous for rear bearings going bad,NOISY is probable an understatement. I wold open door and grab hold of inner tub, try to lift it up a bit, problably a bit of play in there, thats an indication of bearing failure, call authorized servicer possible warr parts

Feb 22, 2008 | Frigidaire FWT449

Not finding what you are looking for?
Amana 3.2 cu. ft. Top-Load Washer Logo

472 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you an Amana Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...