Question about Blaupunkt London MP37 CD Player

1 Answer

How connect amplifire ??

How can i connect amplifire to radio ?? is there any output ??

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

You hook the amp up to the deck with rca cables red and white. you have output rca on the back of the deck also the blue wire labled remote also goes to the amp to turn it on and off.

Posted on Mar 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power but no sound help plz....


well here we go how do you have your pioneer radio connected .
did you run the radio speaker wire out to the factory speaker or did you have an amp connected to the rca output jacks.

1 well if the radio connect by the speaker wire out the
output chip in the radio is fried and needs repair ....

2. if u have a amp connected to power your speakers for sound
check the amp to make sure you have power and no lose connection or speaker wires disconnected.
3. it also possible that the rca jacks are fried too


I no by experience that pioneer loses ground on the audio output jack (rca) well what we did to fix it is..
take and 18 gauge wire stripe back about 1/2" to 1" of the insulation to expose the copper wire and wrap this around the metal casing of the rca jacks and then ground the wire to a ground point do this for both left and right rca jacks...

radiorepair@windowtintingin239.com

Oct 30, 2013 | Pioneer DEH-P3500 CD Player

1 Answer

Hi there I have alpine cda 9856 cd player and it turns on and does every normal however it won't output and sound on either radio or cd. I have checked for any bad connections and can't seem t


Did you make sure you have no shorted or grounded speakers or speaker wires? Make sure you don't have a bad speaker also. If everything checks out, you may have a bad internal output ic.

Jan 15, 2013 | Alpine CDA-9856 CD Player

1 Answer

I get protect error on my car stero, can u help solve the problem. Thanks, VJ


The "PROTECT" message is associated with an audio output issue. This is usually a shorted / damaged / mis-wired speaker output wire(s) between the the radio and speakers or external amplifier, but may be a damaged output transistor inside the radio.

Carefully inspect the speaker output wires of the radio. Make sure all are intact, insulation is not chafed, stripped or otherwise damaged. Tape or repair when found. Double check the wiring (if this is a new installation) to be sure it is correct. Rewire as needed.

After making repairs, power up the radio and see if it works. If it does not, damage has probably occurred inside the radio as a result of the damaged speaker wiring being allowed to exist too long or turning to volume up for even a relatively short period of time. It can also happen if connected to very low impedance speakers. Any of these conditions can cause internal components to fail. The radio will probably have to be professionally repaired to play as expected again.

Hopefully, you'll find and correct a speaker wire problem and it will play again. If my reply was helpful, please rate it "4 thumbs up". Thanks & good luck!

Aug 21, 2011 | Kenwood KDC-MP342U Car CD Player

1 Answer

Just need a pic to see what color wire goes to each of the 20 pins on the back of the deck


Wiring Diagram / Color Codes
1. Power Antenna (dark blue wire) - Connect to power antenna or amplifier.
2. Ground (black wire) - Connect to ground terminal or clean, unpainted part of chassis.
3. Memory/Battery (yellow wire) - Connect to battery or 12 volt power source that is always on. The radio will not work if this wire is not connected.
4. Accessory/Ignition (red wire) - Connect to existing radio wire or radio fuse.
5. Left front speaker - White/Black is negative, White is positive
6. Right front speaker - Gray/Black is negative, Gray is positive
7. Left rear speaker - Green/Black is negative, Green is positive
8. Right rear speaker - Violet/Black is negative, Violet is positive
9. RCA Outputs to Amplifier - Black is front, Gray is rear
10. Auxiliary Input Cable
11. Subwoofer Output
12. Antenna
13. CD Changer

The manual is available here:
http://diversesolutions.org/files/CD4610.pdf

The wiring diagram is under the section Wiring.

Jan 13, 2010 | Jensen CD4610 CD Player

1 Answer

Where are the amps and how do i by pass them for the stereo


The amps are located inside the radio. Most in-dash receivers that provide for "pre-amp outputs" also called "low level outputs" do so by providing female RCA type jacks. These are often found at the end of a short (4 - 6 inch) cable and are usually color coded red & white or red & black (some receivers provide a yellow RCA jack for video in / out, too). To use these RCA audio jacks, you need to realize that one jack is for the left channel source and the other is for the right channel source for a stereo signal. You will have to connect a compatible plug and cable of enough length to extend to a remote amplifier's RCA input jacks. The vehicle's speakers would also need to be connected directly to the same amplifier's output terminals. Using the two audio (left and right) RCA jacks will only allow the radio to control balance of the left and right audio, no fader (front and rear) control is possible. To get fader control, you'd have to either have a radio with four RCA low level output jacks (front L & R *and* rear L & R), or use the radio's speaker (or high level output) wires and connect them to the amplifier's speaker (or high level) input terminals.

All unused receiver wires should be terminated in a wirenut or securely wrapped in electrical tape to prevent accidental contact with grounded metal or other wires behind the dash.

I hope this helps!

Nov 11, 2009 | Car Audio Receivers

1 Answer

I want to connect my ipod to the aux inputs on back of unit


Hello gcd_sun,

The RCA jacks on the back of the Pioneer DEH-1500 are preamp outputs, not inputs. They are to connect an external amplifier for additional speakers or subwoofers.

The output from your iPod is probably "bleeding over" into the receiver detector stage. When the antenna is disconnected, the signal passes into the amp by itself. Connecting the antenna provides enough signal so that both are amplified.

To connect the iPod, you need to purchase a wireless iPod adapter, or a new head unit that includes an "AUX" input or a dedicated adapter for the iPod.

Hope this helps.

Sep 10, 2009 | Pioneer DEH-1500 CD Player

1 Answer

Can i connect ipod adaptor to rca output jacks?


With out an input jack you cannot connect straight to your head unit. The RCA out puts only send a signal out. Your best bet is use an FM transmitter for your Ipod. The sound wont be as good but I can't think of another way with buying a new head unit.

Jun 05, 2009 | Clarion M255 AM/FM Marine CD Player

1 Answer

Speaker hookup


Use the speaker wire outputs on the wiring harness on the back of the radio. The RCA outputs are for using an external amplifier, so you do not want to use them. The speaker wires should be color coded. The front speakers are normally grey and grey with a black stripe for one side, and then white and white with a black stripe for the other side (left and right sides)

The rear speakers are violet and violet with a black stripe and the other rear is green and green with a black stripe. All the solid colors are the positive speaker output and the wires with the black stripe are the negative speaker outputs.

These speaker outputs are on the same harness as the power connections to power up the radio. I believe that it has more than 10 wires on it. I am not sure what socket you speak of that is 10 pin and has speaker outputs. The speaker outputs alone are 8 wires, so the harness will have more than 10 wires. It also has the yellow wire for constant 12 volts to keep memory, the red wire to connect to 12 volts when the vehicle is on, and the black wire for the ground. Then it should also have a blue wire for use with an external amplifier to turn it on or to use for a power antenna to turn it on. You may also find several other wires on it like the orange for illumination and brown for muting the radio when a phone is in use. Those last few wires do not need to be used unless you want them for a specific purpose.

Jan 24, 2009 | Sony CDX-GT420IP CD Player

1 Answer

Amp connection


The only amp wires that connect to the Head Unit are:
Amplifier remote turn on wire to Blue/white at radio
and RCA audio cords to SUB or REAR output RCA jacks.

Aug 04, 2008 | Pioneer 50W x 4 MOSFET Apple iPod...

1 Answer

Sound


hi are you running the sound via an amplifirer or useing the speaker outputs?


Mark
Blue ICE

Feb 26, 2008 | Pioneer AVX-P7300DVD

Not finding what you are looking for?
Blaupunkt London MP37 CD Player Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Blaupunkt Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you a Blaupunkt Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...