Question about Office Equipment & Supplies

3 Answers

I changed the cartridges yesterday- and the alarm button and black light keepflashing

Posted by on

  • mhussey Jul 19, 2008

    now they're all flashing.



    Should there be brown tape on the back of the black cartridge?



    It says E-5 but I cant find how to do the alignment



    Thanks

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 382 Answers

Hi,
Can you please specify the model of your printer so that you can assisted more perfectly..Thank you!!..Regards!!..

Posted on Jul 19, 2008

  • Natesan Sabesan
    Natesan Sabesan Jul 19, 2008

    Hi,
    There shld be no tapes on back of the black catridge!!..try the following steps which will help you

    1) With the printer powered off but connected to a power source, press the Power button while pressing and holding

    the Stop/ Reset button.
    2) When the Power LED is lit, press the Stop/Reset button two times while pressing and holding the Power button.

    3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a

    service mode. (Waiting formenu selection)

    4) When the LED lights in green, press the Stop/Reset button the specified number of time(s) according to the

    function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in

    orange and green, starting with orange.)

    The number of the Reset

    button pressing

    LED Function Remarks

    0 time Green Power off

    1 time Orange Service pattern print

    2 times Green EEPROM print

    3 times Orange EEPROM reset

    4 times Green Waste ink counter reset See waste ink counter reset

    procedures below.

    5 times Orange Destination setting See Destination setting

    procedures below.

    6 times Green Print head deep cleaning

    11 times Orange Button / LCD checking

    12 or more times Returns to a menu selection


    Thank you!!..regards!!.. :)


×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 97 Answers

Press reset, they should go away. what make and model is this printer?

Posted on Jul 19, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 19,396 Answers

Check cello strip on cartridges.

Posted on Jul 19, 2008

  • Ginko
    Ginko Jul 19, 2008

    First of all post your printer model here, so that we can provide more specific help.
    Try first disconnecting printer power cable (unplug it, turning off is not enough) for five minutes, this will reset the printer.
    Check that all door are closed and that there is no paper fragments inside the printer.
    Go to your printer software menu, under start button, chose tools and do alignment and nozzle check.


  • Ginko
    Ginko Jul 19, 2008

    There should be no tape on top of the cartridges, remove tape strips.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My MX922 printer worked well this morning. All cartridges have ink but ALL lights under the cartridges are on and print comes out blank. There are no error codes or anything abnormal displayed


This problem is mainly happens to all inkjet printers. If your printer print blank pages then please at least once go to official site of Canon and check whether there is any printer/scanner drivers update is available or not. If yes then download it. Also check your ink cartridges. Because if there is no print on paper that means your ink might be dry.Sometimes it clog the print head. If your ink cartridges get dry change it. Or you should clean your printer's print nozzle by using printer's control panel. I hope all these suggestions helps you. If doesn't then watch Canon MX922 Manual English

Jan 12, 2017 | Canon Pixma MX922

1 Answer

I replaced the K cartridge and i get this caution. I-Unit End Replace K


If "[Color name] Toner Empty. Replace with a new toner cartridge." is displayed and printing stops, replace with a new toner cartridge.
([Color name] indicates one of the following: C or Cyan, M or Magenta, Y or Yellow, K or Black.)

Jan 10, 2017 | The Office Equipment & Supplies

1 Answer

BROTHER P-TOUCH IS not printing


It is obvious it has a failed electronic component, since these are not repaired/exchanged except when they are under warranty best thing to do is just replace it.

Jan 09, 2017 | Brother Office Equipment & Supplies

1 Answer

My printer brother dcp7065dn disply 71 and72 error


This is codes for the ink cartridge. The code means there is a problem with the cartridge. Change them both and restart the machine.

Jan 13, 2015 | Office Equipment & Supplies

1 Answer

My 202 doorbell does not "react" if the button is pushed AFTER my neighbor unlocks his car by using his remote key. Can I change the frequency range of the doorbell?


look for a cover that has small switches under it. You can change frequencies there. You must match the door button the same way .

Nov 19, 2014 | Office Equipment & Supplies

3 Answers

My Epson WF-3640 is printing with gaps in the text. How do I fix this issue?


Make sure you should remove shipping tape from the ink cartridge. These taps are used to protect printer during shipping but you have to remove it before starting printing. Beacuse these taps prevent the ink to entering in print head. If you will not found shipping tape in your printer then there is terr off strip, remove it. The tear off strip seals the the vent holes on the top of the cartridge to prevent it from drying out on the shelf or during shipping.
After ensuring that the shipping tape has been removed, run the printer's "Head Cleaning" utility to prime the cartridge, then print a test page.
See full detail at- http://guideusermanual.com/product-name-workforce-wf-3640-manual&po=152836&lang=English

Sep 18, 2014 | Epson WorkForce WF-3640 Wireless Color...

1 Answer

Why is print quality poor after inserting new ink. Copies are faint and have lines


the cartridge is clogged with ink that has dried and reduced the slit. you need to replace the cartridge with a new one. it happens usually if you recharge the cartridge 3 or 4 times with compatible ink.

May 07, 2014 | Office Equipment & Supplies

1 Answer

Colour cyan not printing


Did all of the packaging come off the toner successfullywhen first installing. Can you see cyan toner on the transfer roller? (Black roller on actusl cartridge)?

Dec 08, 2013 | Office Equipment & Supplies

6 Answers

Printer won't recognize cartridge


I had the same problem. I'm not sure but I think I replaced the cartridges when the printer was on because I turned the printer off and removed one of the cartridges. When I turned the printer back on it recognized that cartridge but not the others. I turned the printer off again, rmoved all cartiridges and put them back in when the printer was still off. When I turned the printer on again I had no problems. So...try turning off the printer, rmove all cartridges, then put them back in and restart printer. Hope this works for you .

Nov 28, 2007 | Epson Stylus 2200 InkJet Photo Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

100311 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

66433 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...