Question about Asrock P4VM890 Motherboard

2 Answers

P4VM890 + new videocard! No boot up!

I bought a new video card - giga-byte HD 3650!
1st i go'ed to bios, and disable onboard card.
I uninstaled videocard drivers.

then i put videocard in slot.
I started pc, and there is no boot up, just blank screen and red hdd light!
I tired everything! Cleared CMOS too, and nothing!

Posted by on

  • 6 more comments 
  • egils327 Jul 19, 2008

    Sorry for my bad english! :(

  • egils327 Jul 19, 2008

    Thx, what is reboot disk. I thin is stupid question.... but i dont understant this quesiton. And i have bad english :/ i am sorry :(



    Btw i have 500w power supply!

  • egils327 Jul 19, 2008

    oh u mean windows disk thx

  • egils327 Jul 19, 2008

    I didnt find my driver cd :( :(



    what i need to do now

  • egils327 Jul 19, 2008

    Ok thx, but when i put videocard, there is no bootup, computer dont start, only blank screen and always red hdd light!

    And i found my driver disk!

    U said need windows disk, why. I cant start PC whit my new videocard on! I hope you understand me.

  • egils327 Jul 19, 2008

    Ravege i dont understand you!

    Ok, i need restart pc, then need put video card, i understand, i need put videocard when PC is Turned ON????



  • egils327 Jul 19, 2008

    It didnt help, i do all what u say and nothing!

    I only see BLANK SCREEN and no sounds of boot up NOTHING JUST BLANK SCREEN! :( :(





  • crash83 Jan 28, 2009

    i have a p5p800, and if my old x800agp is installed , my system boots just fine, i try to install any other agp card, yes working agp cards i have tested that do infact work, my system refuses to boot up. all power connections are made, all firmware, bios, chipset driver are updated. my mobo just wants my x800 in it to boot and i'm at wits end.

×

2 Answers

.................................................................


yea thx, eh, ganna dump my mobo!

:/ Ravege i think your help was DUMP realy DUMP



sry...

Posted on Jul 21, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 327 Answers

Welcome to fixya

Well i never did it that way but ok

your going to have to reboot the computer with the reboot disk ,,

once thats done turn off computer and install the video card and then also insert the drivers disk that came with the video card
this should work has for me and i have done 100s of video cards
Although if you bought a good video card and still have a 400w power supply your going to run into trouble make sure you have a 500w power suplpy or better to run a good video card ,,,,,

i hope this helps you out have a good day:)

Posted on Jul 19, 2008

  • 3 more comments 
  • victoria bennett
    victoria bennett Jul 19, 2008

    reset disk ...the cd with windows on it?
    this help any?


  • victoria bennett
    victoria bennett Jul 19, 2008

    go back in to bios and make sure you us the cd rom drive

    as master boot



    this should help

  • victoria bennett
    victoria bennett Jul 19, 2008

    make sure the computer has nothing new in it then reboot the computer



    and the red light on the hd ?



    after you rebott the computer then you want to put in the new video card not til your done with the reboot



  • victoria bennett
    victoria bennett Jul 19, 2008

    no reboot computer with windows cd



    then turn off and put in new video card



    hook the video card up to montior





    then turn on computer and install the software for new video card

    t

  • victoria bennett
    victoria bennett Jul 20, 2008

    then sounds like you should take to a repair shop you messed something eles up ....sorry i could not be no more help :)



×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Recently I bought the ATI SAPPHIRE Radeon HD 6770 flex edition on ebay. Today it arrived and I put it in my motherboard MCP73PV ( from oem pc Acer Aspire M3641) (also i have a new power suply 450 Watt so...


in the bios, there are usually settings for onboard devices. try turning off your onboard vga in the bios. and/or enabling/disabling pci-e video settings in the bios. it also helpful to ensure there is a monitor plugged into the video card. if there are 2 video outputs on the new card, try plugging the monitor into one, reboot, if nothing shows up, plug the monitor in the other one, reboot, if nothing shows up; i dont know :)

Sep 12, 2013 | Computers & Internet

1 Answer

My asrock p4vm890 is has invalid mac address for both cmos and bios


The MAC is the unique identifier for the onboard LAN chip - if it's invalid then the chip has been fried - disable it from the BIOS and install a new PCI LAN card.

Mar 27, 2011 | Asrock P4VM890 Motherboard

2 Answers

How do you disable the onboard graphics on an emachines C2825? I am attempting to install a Sapphire Radeon HD 4650 AGP video card, but my computer will not boot when i plug in the new video card. I have...


First of all that motherboard is too weak to fully use that video card, you could get the same framerate in games using a video card 2 generations older. 
Proper way of installing a new card:
1. uninstall the driver of the old one and reboot in BIOS - in there put all settings to auto;
2. shutdown the pc and install the new card; connect the monitor to it;
3. boot into BIOS, disable the onboard video card and reboot;
4. boot normally and install the driver.

Jul 24, 2010 | Intel D845GVSR Motherboard

2 Answers

PCI Video wont work with Gigabyte GA-K8VM800M motherboard


hey try the removing cards.....
window 7 may took up it best when no such changes are around..
! Gb or 2 RAm is enough to get run your Win 7
and sound card is noot required untill you have 4 or more speakers

Feb 12, 2010 | Gigabyte GA-K8VM800M Motherboard

2 Answers

My biostar g31 -m7 te motherboard does not boot when i try to add a msi rx800 pcie video card,,sometimes i get a overclock fail message after i remove the card and reboot,,,how do i get this card to work...


Turn the computer off.
Remove the PCI-E video-card.
Boot the computer.
Press DEL to "enter BIOS setup".
Disable the "onboard video" adapter,
or set the highest video-priority to be the PCI-E slot.
Save settings, but do not "exit" from BIOS setup.
Turn the computer off.
Install the PCI-E video-card.
Disconnect the video-cable from the onboard VGA-port,
and connect the video-cable to the new video-card.
Turn the computer on, and the video-output through the new video-card should be displayed on your monitor.

Nov 05, 2009 | Biostar G31-M7 TE Motherboard

2 Answers

I just installed a new sapphire radeon atlantis 9600 pro video card 256GB ... everything installed and ran well until it restarted...now the monitor will not receive signal


check the bios and make sure that the onbord video is disabled, pull battery off the motherboard and reset everything if nothing else works, Be sure to plug monitor into the onboard video card so u can access the bios, also check that cable is snug at both ends(i know silly but you would be amazed) if stilll nothing fallback on other videocard and test new card in another computer, was the videocard seated snugly and tightened down good?

Jul 15, 2009 | ASUS P4S800-MX Motherboard

1 Answer

HOW TO DISABLE MY ONBOARD GRAPHIC CARD??


For user BIOS21 & julio1963,
How to enable you're (Add-in AGP video card) & disable the onboard, integrated S3 graphics UniChrome 2D/3D PCI graphics card.
Enter you're bios. Open you're user manual to page 3-13. Integrated Peripherals. Go to, Init display first. Set to AGP.
(Not to PCI). That is all you need to change. The MSI bios will than see you're add in AGP card & automatically disable the PCI S3 graphics, (Onboard) card.

Enjoy!
If I can help you further, feel free to post here.
Please, each user's vote this issue as a fix, if this helped you to get you're bios to see you're new AGP graphics cards.
Mike


May 31, 2008 | MSI KM4M-L Motherboard

1 Answer

My pc still won't boot up


The beeps are beep codes. Were they short or long? Also do you know who makes your BIOS?

Jul 26, 2007 | EliteGroup P4VMM2 Motherboard

1 Answer

My pc doesn't boot up


Did you have onboard video before? What is the video card? AGP8x, AGP4x, PCIe? If you had onboard video, you'll need to change the settings in the BIOS and disable the onboard video. You'll have to plug in at the onboard to access the BIOS.

Jul 23, 2007 | EliteGroup P4VMM2 Motherboard

Not finding what you are looking for?
Asrock P4VM890 Motherboard Logo

Related Topics:

596 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asrock Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Mark Taylor
Mark Taylor

Level 3 Expert

728 Answers

David
David

Level 3 Expert

756 Answers

Are you an Asrock Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...