Battery dead, boosts do not work, shift lever stuck in park. How do I get the shift lever to release so I can put in neutral?

If you're unable to push the gear shift into neutral in a 2007 Chrysler 300 when the car battery is dead and the key has stopped working, there is a solution that can help. You can locate the shift interlock override mechanism to manually put the vehicle into neutral. First, remove the plastic cover or cap located near the gear lever to reveal the shift interlock override slot. Insert a small screwdriver or a similar tool into the slot and apply gentle pressure while simultaneously attempting to move the gear lever into neutral. This should release the shift interlock mechanism and allow you to shift the car into neutral. It's important to exercise caution and consult the vehicle's manual for precise instructions tailored to your specific model, as the process may vary slightly.

we can not see you shift.
PRNDL , car will crank in N and P, both.
park lockout is safety feature.
all fuses good.
battery charged (under hood)'
brake lamps most work.
sure likeage can fail for sure. they told you the truth.
park lock out locks it in to park
and can not be shift out until brake applied and brakes glow. rear (brake fuse not blown)
then if did shift out of park and not lever is dead
that means the linkages is bad.\

NO it will start in Neutral. all cars do but the most rare of odd honda's
fly past neutral means cable is broke me but cant feel your shifter lever.
the shifter has 2 ends of linkages, top side and under car. to trans.

removing the PRNDL switch means engine can never crank again, P/N now dead.
my guess is this is cave man simple bad linkage.
a simple lever device, and link

no it doesnt

First explain why it won't go into neutral. This may be the problem for no start.

shift lever does not move out of the PARK position with the ignition ON and the brake pedal pressed ?

There is usually a little hatch near the gear selector that has a rubber plug over it and you take that out and depress a lever in the hole with a key and then you can move the gear selector into N and push the car out.

if you look on the center council where the shift lever is you will see a small plastic button on the drivers. Remove the button. Insert a small screwdriver into the hole and push down. You will then be able to move the shift lever into nuetral and push the car.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Try putting it into neutral, then apply the parking brake, then try to remove your key.

The problem is the BTSI or Brake-Transmission Interlock. It is a safety feature designed to allow the car out of park only when the brake is pressed, and only allow the key to turn to lock in the ignition when properly parked. Your car is not "recognizing" that your in fact, properly mechanically parked. If my first instructions did not work; try the following...you will need both hands simultaneously and one foot.

*This only applies if your battery is not dead*

Apply the brake;
then with your right hand, push in your shift lever button and push the lever forward as far as will go...hold firmly.
Then with your left hand, try to turn your key to lock and remove it.
However if your battery is dead, look at your shift console. You will see a plastic tab next to your shift lever, it may have a "12V" label next to it. Beneath this tab is the switch for emergency power to get your key out of the ignition on a dead battery.

Shifting to NEUTRAL
To shift the transfer case to NEUTRAL, first make sure
the vehicle is parked so that it will not roll:
1. Set the parking brake.
2. Start the vehicle.
3. Connect the vehicle to the towing vehicle.
4. Put the transmission in NEUTRAL (N) or have
the clutch pedal pressed for vehicles with
manual transmission.
5. Shift the transfer case to 2HI.
6. Simultaneously press and hold the 2HI and
4LO buttons for 10 seconds. The red NEUTRAL
light will come on when the transfer case shift to
NEUTRAL is complete.
7. Shift the transmission to REVERSE (R) for one
second, then shift the transmission to DRIVE (D)
for one second or FIRST (1) for vehicles with
manual transmission.
8. Turn the ignition to OFF.
9. Place the transmission shift lever in PARK (P) or
FIRST (1) for vehicles with manual transmission.
10. Release the parking brake prior to towing.

************************

Shifting Out of NEUTRAL
To shift out of NEUTRAL:
1. Set the parking brake and apply the regular
brake pedal.
2. Start the vehicle with the transmission in PARK (P)
or FIRST (1) for vehicles with manual transmission.
3. Press the button for the desired transfer case position
(2HI, 4HI, AUTO 4WD or 4LO).
4. Put the transmission in NEUTRAL (N) or press the
clutch pedal for vehicles with manual transmission.
5. Shift the transmission lever to the desired position.
After the transfer case has shifted out of NEUTRAL,
the red light will go out.
6. A re-engagement sound is normal when shifting out
of NEUTRAL.

u can get someone to hook up there car to jump it or at least get power to put in neutral.