Question about JVC AV27WF36 TV

1 Answer

JVC AV27WF36 TV

The light of "on timer" stays solid and the tv does not turn on no picture or audio i can once in a while press the power button and the timer light will go off but when i press it again it comes on and doesnt go of easily

Posted by on

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I have the same problem

Posted on Oct 22, 2008

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While watching tv I touch something on the remote to make the tv go into "on timer" The red light is blinking. I have removed power then on again the remote and tv controls work but after 4...


Check the remote carefully for a stuck button. You may have pressed a button and it went a bit crooked getting stuck.
Also, remove the batteries of the remote and try operating the TV manually. If the remote is the cause, the TV will work correctly once you remove the batteries.
Another way to check is by using a digital camera, like the one in a cell phone. Turn on the camera and point it at the remote. If you see a white light coming from the transmitter, the remote is sending a signal. Look for a stuck button.

Jan 04, 2011 | JVC AV-27920 27" TV

1 Answer

Blinking timer light, No picture or sound.


Ur high voltage is dead,the FBT,the flyback transformer,the big black block of plastic with a red wire with a cap hook to the CRT(tv tube).That is dead.

Sep 27, 2009 | JVC AV-36D302 36" TV

2 Answers

Need code for Innovage jumbo universal remote for a rca tv


The Innovage Jumbo users manual lists over two dozen RCA TV remote codes. They are:

000, 003, 004, 005, 007, 009, 011, 015, 048, 082, 092, 094, 096, 098, 101, 102, 103, 107, 113, 125, 129, 167, 179, 187, 188, 191, & 194.

To program your remote by entering a code, follow these steps:

  1. Turn on your TV.
  2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
  3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
  4. Enter the first set of 3-digit codes from the list. The LED will blink once every keypress. After the 3rd digit, the red LED will turn off indicating that the code was recognized for the device. If the code was not compatible, the LED will flash several times and you need to return to step 2 to try that code again or to try the next code in the list.
  5. After the LED has turned off, aim the remote at the TV and press ON/OFF. If the device turns off, you have used the correct code and the remote was successfully programed. If the device does not power off, return to step 2 and try again with the next code in the list.
If you can't be bothered to enter each of those codes one at a time, you might consider the auto-search function.

To have the remote try each TV code it knows one at a time, follow these steps:
  1. Turn on your TV.
  2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
  3. Press the TV button on the remote so that the LED blinks once and then remains solid red.
  4. Press the ON/OFF button slowly and repeatedly until the TV turns off. The LED will blink once each time you press the ON/OFF button.
  5. Once the TV turns off, press the ENTER button to store the code and the LED will turn off.
I hope that helps.

Sep 17, 2009 | RCA TruFlat 27F520T 27" TV

1 Answer

Tv picture is going out and standby/timer light blinks


Hi Kevin!

The issue may be related to the projection lamp in the TV and replacement may be required. However, before replacing the projection lamp in the TV, you may perform the troubleshooting steps mentioned below.

Please disconnect all the cables from the TV including the power cable then reconnect them after two minutes. Please make sure that the the power cable from the TV is directly connected to a functional wall outlet. Next, you may try connecting any other video source such as cable box, DVD player, Blu-Ray player, Playstation, etc. If the issue persists then try resetting the TV to the original factory settings.

Please follow the steps mentioned below to reset the TV to the original factory settings:
(i) Turn the TV ON.
(ii) Press and hold the Reset button on the Remote Control supplied with the TV, then press the Power button on the front panel of the TV.
(iii) Next, release the Power button. The TV will turn itself off, then back ON.
(iv) Release the Reset button.

If the issue persists then you may replace the projection lamp in the TV.




Jul 12, 2009 | Sony FD Trinitron WEGA KV-32FS120 32" TV

1 Answer

Jvc tv av-32d502 timer light is flashing will not turn on


Hello, I am a tv tech. I worked on a JVC AV-32D502 today. Problem: led flashes / no power or picture at all. Same as trobertson52's set. The microprocessor is bad in my machine. trobertson52, if your sets' relay does not click when the power button is depressed you most likely have the same problem or the standby power circuit is at fault. That circuit supplies +5 volts to the micro.

Edtal you have a different problem with your machine. Your machine is going into shutdown. A number of circuits could cause this and would need to be looked at by a technician to determine exactly which circuit is at fault. High voltage transformer (HOT) \ Vertical Circuit \ Power supply are the most likely causes.

barneyinNC

Sep 25, 2008 | JVC AV-27020 TV

2 Answers

JVC 27" D series


there is another problem that requires a tv repairmans expertise when the timer light flashes continuosly ,and the power is not restored.

Apr 21, 2008 | JVC AV-27D502 27" TV

1 Answer

JVC TV crisis.....HELP


yes... i actually work at verizon the tv is to old for fios because fios is so advanced we run off ot 720 to 1080 depending on areas. what kind of box is it? is it the hd box or stb>

Feb 13, 2008 | JVC AV-32230 32" TV

1 Answer

Image doubled when using 480p


No it is only 480i with component cable support.

Jul 27, 2007 | JVC AV27WF36 TV

Not finding what you are looking for?
Standard (CRT) Televisions Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top JVC Standard (CRT) Televisions Experts

The Knight
The Knight

Level 3 Expert

68427 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

Jaime Hernandez

Level 3 Expert

2267 Answers

Are you a JVC Standard (CRT) Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...