Question about Audio & Video Receivers

1 Answer

Dont have no sound - Audio & Video Receivers

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 682 Answers

If you have power in-check the following:
1-headphone jack is inserted inside pull the jack out.
2-master volume in low level.
3-mute switch or button is on-please make it off.
4-bad setup of speakers re setup again.
5-speakers cables are pulled out or disconnected.
6-wrong selection of input source(you must confirm what did you want to play).

Posted on Jul 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No sounds from my yamaha HTR6030 Display is OK. All function keys working.Relay clicks. But no sounds.


Try connecting different sources to different inputs or fm source if nathing produces sound I would recommend to have it check by a tecnitian

Aug 19, 2016 | Yamaha Audio & Video Receivers

1 Answer

I turn the power on to my RX-318 and a few seconds later it sounds like something else is kicking on....then I dont hear any sound from my speakers. I dont know if theres a fuse blown, the amp is going out...


Sounds like the automatic circuit protection. Check to make sure you have good speakers and NO shorted wires to them. Too many spearkers conected to the outputs will cause the same problem.

Sep 12, 2011 | JVC RX-318 Receiver

1 Answer

I dont have sound in my pc


Hi. Maybe the driver of your sound device is corrupted. Try to re-install the driver. Reply here the model of your sound device then I will help you to look for the best driver to your sound device.

May 21, 2011 | Audio & Video Receivers

1 Answer

Windows Media Player cannot play the file because there is a problem with your sound device. There may not be a sound device installed on your computer, it may be in use by another program, or it may not...


you dont have the correct sound driver installed on your pc you need to find the manufature of your sound card and install the correct driver to suit it

Sep 25, 2010 | Audio & Video Receivers

1 Answer

No sound, Tried unplugging system for several days no help. Checked all wiring to speakers, looks ok. made sure speaker switch in correct position.


if you have a sound card you might need to reinstall the driver. if you dont have one double check the sound settings on the computer. maybe the speakers are not active

Jun 27, 2010 | Sherwood R-925

1 Answer

No sound


It looks from the picture that this thing has a built in tuner. Try that first. If you are not getting sound from the tuner then inspect your speaker connections. Does this receiver have A/B channels for different speakers or different modes for surround sound? Did you try adjusting those? It is highly unlikely that it is broken, good luck!

Dec 14, 2009 | Sony STR-DE897 Receiver

1 Answer

No sound from speakers.


the earings were stood out bigger on screen than in real life i dont know my maths very well but i thought as this programme had shown it was a bargain i can walk into any jewel store (which i have) and the same earings are $30 i dont have time because of work so thank you anyway

Dec 16, 2008 | Audio & Video Receivers

1 Answer

Rear Speakers dont work -Audi 2004 A6 sline Symphony II


you may have a loose wire somewhere or the wires comming from the headunit could be broke or damaged

Mar 04, 2008 | Audio & Video Receivers

1 Answer

No Sound


well, if it powers up, youve still have hope// check and see if you can see a fuse holder at back of stereo... or go to a radio shack or electronis place and get whats called 'contact cleaner' ( may go by a different name, make SURE you know that the salesperson knows what your talking about..PS.you dont have to buy the pricey stuff, but dont get the cheapest either.) then UNPLUG stereo, make sure its not hot ( dont have it on for a long time before working on it) then pull out the knobs on the front ( the volume,left/right,etc) spray a LITTLE bit into the stereo where the plugs go.dont drench it, a little goes a long way) after spreying it in, turn the knob back and forth so it gets to all the points.... make SURE its dry before plugging it back in, you can tell if you see any moisture where you sprayed.( another reason, not to spray much) i usually let my stereo and tvs dry over night before trying them.while your waiting, may as well take a cloth and clean the face, get any cruddies off... good luck

Mar 12, 2007 | Kenwood VR-405 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68157 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...