Question about Power Generators

3 Answers

Changing blades on Huskee LT4200 Riding Lawn Mower

I can't seem to break the bolt loose to change the blades on my riding lawn mower. I have tried impact driver and wrench with long pipe. Are these bolts reverse threaded or what???

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wd 40 is a luberecant,, blaster is a penterant ,,works much better, been using blaster sence 1960....
Bill

Posted on Apr 25, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 254 Answers

No they are right handed thread just correded on. What I would try is heating the bolt up then spraying W.D. 40 on it let it set for 5 mins then try breaking it loose. Just one thing spray the W.D. 40 while its hot but not near a flame.

Hope this helps You
please rate me

Posted on Jul 24, 2008

Thanks Burzerko,
I soaked them with Blaster and cranked my aircompressor up a notch and zapped them in short bursts with my impact gun and they finally gave up. I was working too hard and not working smart. I was really believing they were left handed threads for awhile.

Never underestimate the power of very stupid people in large groups. I know dat's right..

Posted on Jul 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Carb bowl gasket needs replacing were can i find one or a carb kit


Your going to have to go to a Cummings Onan Dealer for the gasket. You can however walk in to any lawn mower repair shop with the part in hand. (example match up) You will save money and walk out with the part you need in hand. I can't remember if it is the Honda GX series gasket or the Tecumseh L series that will work. Honestly is has been a while so you would be better off seeing the exact match up at the Local Lawn mower Parts source. Most RV & or Marine equipment service dealers have them also. Very common item.

Kelly

Kelly

Sep 21, 2010 | Watts Onan Portable Generator - 4000 ,...

1 Answer

My fg6000mk 11 horse had valve break and ruined the head. where do i get parts


I am pretty sure that is a Honday 11 Hp engine. The part number for the head is

030730Q01F000 (CYLINDER HEAD ASSEMBLY)

Most lawn mower parts supply places can have your part in hand in a couple of days. I was not able to find a price for the head but I know they are not cheap.

When you call or visit the lawn mower parts store make sure you have the engine model number with you. They amy even ask for a serial number. The numbers are near the oil drain plug toward the bottom of the crankcase but under the starter.

Let your fingers do the walking on the phone first... you could drive about for sometime before finding the shop that can help you. (i.e yellow pages Lawn mower repair)

Thanks for using FixYa!

Kelly

Feb 19, 2010 | McCulloch 13HP 338 Cc Portable Generator #...

2 Answers

Kohler 19 hp runs then backfires and stalls when heated up


Check that the keyway for the flywheel to the crankshaft hasn't sheared. This is a common problem that throws timing very far off causing backfire and no-starts.

Sep 24, 2009 | Kohler CH25 PA-CH730-0040 Command Gasoline...

1 Answer

NEED MANUAL FOR MURRAY MODEL #465603X92


There is a problem with your model# it shows up as Riding Lawn
Mower, can you check that again and get back with me.
Ralph woodworking57@hotmail.com

Sep 15, 2009 | Briggs & Stratton Power Products 5,550...

1 Answer

Craftsman riding lawn mower


Make sure you are fully engaging your clutch. If you are, then the shift linkage needs to be adjusted.

Aug 25, 2008 | Power Generators

1 Answer

Lawn mower won't run


make sure the tank has fuel and replace the fuel filter

Jul 20, 2008 | Power Generators

1 Answer

Mower will not stay running


Sounds like a lack of fuel. If it has a briggs motor replace fuel pump diaphram in carb.

Jul 19, 2008 | Power Generators

1 Answer

Weight Limt


thats a great question and i am wondering the same thing i weight in at about 240 and it seems to ride fine beside the noises it make but im thinkin the noise is because it is brand new... i have heard nothing about weight limits and read the entire manual and read nothing about weight limits so im assuming there is no limit .....

Jul 12, 2008 | Power Generators

2 Answers

Engine wont start


If you are talking about a riding mower, then try turning the blades off before starting mower. I had my blade switch in the on position once and could no figure out why the tractor wouldn't start until I pushed the mower into the garage.

Jul 08, 2008 | Generac Guardian 0A18010 - battery...

Not finding what you are looking for?
Power Generators Logo

Related Topics:

2,363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Power Generators Experts

John Trevino

Level 3 Expert

1378 Answers

EugenesDIYDen
EugenesDIYDen

Level 3 Expert

479 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Power Generator Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...