Question about PC Desktops

1 Answer

Installaion of wireless mouse - PC Desktops

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 36 Answers

Does it have a cable option two, if so install like this, then change to wireless after restarting computer after finishing installing drivers (cd)

Alternatively install drivers with Your old mouse plugged in, then see if it picks it up after - You did get a install cd with the mouse yes? if not check manufacturers website for model

Posted on Jul 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I just purchased my first laptop...and do not like the touchpad...I want a wireless mouse...can I use a wireless mouse without being connected to wireless...in other words can I use a wireless mouse while...


Yes, the mouse most likely uses Bluetooth to communicate with your laptop and is independent of your wired/wireless connection to the internet. The mouse should have come with an adapter that plugs into one of your USB ports. Plug it in and once the drivers load (automatically), your new wireless mouse should be working!

Sep 08, 2010 | PC Desktops

2 Answers

The microsoft wireless mouse stopped working after a power failure. I get a message that says the USB device is not there. But I cannot navigate my computer w/o the mouse


The Microsoft wireless mouse comes with a wireless receiver, right? Before you do anything, the first thing that you can try is to replace the batteries with fresh ones.

If same problem occur, try to connect the wireless receiver into different USB ports of the computer. Then check if your wireless receiver and mouse has a connect button. If it does have connect buttons, briefly press the connect button on the receiver, then hold down the connect button on the mouse for 5 seconds. Then release the connect buttons.

If you get the same problem, hold down both connect buttons (receiver and mouse) at the same time for 5 seconds.

Last, try to connect the wireless receiver into different computer. If you get the same problem, send the receiver and mouse to the manufacturer for repair.

Thank you and good luck!

Jun 15, 2010 | HP PC Desktops

1 Answer

Activating COT2 wireless mouse


Your ACME COT2 wireless mouse must have come in two pieces, the USB connector the mouse itself.
Insert the USB connector of your wireless mouse to your Toshiba Satellite and press simultaneously the button in your USB connector and the button in the wireless mouse. This is done in order to pair the mouse to the USB connector.

Jan 05, 2009 | PC Desktops

1 Answer

My wireless mouse suddenly stopped working, its on, the lights are blinking but the computer doesn't respond to it, its a microsoft wireless optical mouse.


To Troubleshoot:
1.) try to change the battery of the mouse
2.) try to connect the USB of the receiver of wireless mouse to the other open usb slot
3.) try to use your wireless mouse to other computer to troubleshoot

Sep 30, 2008 | PC Desktops

1 Answer

Wireless mouse all of a suddon stoped working. everything is plugged in fully charged , have tried the connect button along with many others. 7 button centrios laser mouse.


Nice mouse.

I've had some problems with wireless mice in the past, so I will just list the causes and see if one fits the bill for you.

1. Did you move the USB transceiver (this is the device that communicates with the mouse) from one USB port to another? If so, uninstall the mouse and reinstall it using the CD that came with your mouse.

2. Do you have any other wireless devices in the vicinity of your mouse that use a radio frequency rather than infrared, such as a wireless keyboard? If so, you may have a conflict.

3. Were you provided instructions on resetting the RF channel and/or ID code of the mouse? There is a small chance that the channels/codes between the mouse and the transceiver were scrambled and you may need to sync them again.

Hope one of these helps!

Jul 27, 2008 | PC Desktops

1 Answer

My targus amw2002ca wireless mouse will not work and driver is upto date and comp says is working fine


Un-install the mouse driver. Disconnect the wireless mouse hup and shut down your computer. Re-attach your wireless mouse hub and your computer should reconize the hardware and automaticaly install the hardware driver.

Jun 17, 2008 | PC Desktops

1 Answer

Wireless mouse will not work


Look on the bottom of the mouse for a connect button and also on the wireless receiver. Push the button on the mouse first, release and then push the button on the receiver.

Mar 27, 2008 | PC Desktops

1 Answer

CANT GET WIRELESS MOUSE TO WORK


Try changing with a new set of batteries. also try to reset the connection of the wireless mouse and keyboard. you can locate a connect button on both the reciever and wireless keyboard. press both of them together and release them. this would reset the connection. try doing the same for reciever and wireless mouse connect buttons. this should work. also check for any possible alignment issues.

Jan 15, 2008 | PC Desktops

Not finding what you are looking for?
PC Desktops Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top PC Desktops Experts

joecoolvette
joecoolvette

Level 3 Expert

5660 Answers

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Are you a PC Desktop Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...