Question about Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Beeping noise and run of C codes

I woke up this morning to my washing beeping and when I looked I believe the code was FE and that is not in the manual. (my lid was open) So I hit stop and then a few minutes later after shutting the lid it ran thru a series of C0, C1 ect... C codes & beeping again ?? Again not in the troubleshooting section so have no clue what is going on. I had to leave for work so just unplugged machine. I've been reading other problems on this site & wonder if that is something to do with F1. I don't remember having that code ever & until now, our machine has worked pretty well. Please help if you know what the C code series would be or have suggestion. Thanks! Sandy

Posted by on

  • johwa_77 Aug 17, 2008

    Sandy, we have the same exact problem. Around 4am this morning the machine started running through the cycles. We opened the lid and it continued to run through the cycles. Finally, we just unplugged it. But the output was C0, C1, C2, etc. I thought that might have stood for Cycle 1, 2,3, etc. Looking for a solution. THanks, Will


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,028 Answers

Sandy the top of the washer pops up there are clips under the edge that have to be pressed in once you have the top up look on right side there is a service manual with codes every time i work on one i have to look up codes can't remember them all to save my life goo luck

Posted on Jul 17, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Front loader. Why does it run for about 30 seconds, then stops, beeps, and displays code e64?

Good Morning friend, thank you for your post!
I see that your Frigidaire frontload washer runs for 30 seconds, then stops, and produces an error code "E64". It appears that might be an invalid error code. I would recommend performing a reset on your washer and you can do that by unplugging the power cord for at least ten minutes. If you continue to receive the error code or a new error code please reply back. I would like to assist you further. -Matt

Jun 04, 2015 | Frigidaire Washing Machines

2 Answers

FE code on LG washer.

The FE code is an excessive water supply if the water is continuously running into the machine it may be due to a failing inlet valve or stuck float switch since you mentioned the drain pump filter being changed it could be that the old filter was restricting the flow.

Apr 28, 2015 | LG WM Washing Machines

1 Answer

The water in the tub is draining out on its own and the led indicator shows FE

The FE error code indicates water is overflowing due to the faulty water valve. So, the 4-way water valve will need to be replaced.
Here is the part you need.

Oct 20, 2012 | Washing Machines

1 Answer

Samsung washing machine

Based on my experience, the same thing happens to me as you have mentioned that it happens every end of a cycle. I doubt if it was a fan error or a frequency error. for me, its just a simple overload for the autodrying. for example on my model. the manual says autodrying cotton-cupboard dry must be max 3 kg. since you cannot measure your wet clothes and it sometimes exceed the 3kg autodrying, that is when the FE comes out. but when i remove some clothes or spin the laundry again and put it into drying, everything works fine. when i use the machine with minimal clothes say 2kg dry, the whole cycle up to drying work fine without FE errors.

So i believe its just an error for drying overload. also the manual says nothing about FE nor Error code for drying overload.

Hope this help.

May 31, 2012 | Washing Machines

1 Answer

Washing mashine MW511 top loader was running good but this morning tried to start but it is making a beep beep tone and flashing lights

It is giving out a fault code,
Of the 8 wash progress lights, tell me witch are on,
I will tell you the fault code and info on how to fix.

Jan 29, 2012 | Fisher and Paykel Washing Machines

1 Answer


you can cancel the beeping sound by pressing the cancel button. look for an error code and check the meaning at the manual that came with the washer.

Jun 28, 2008 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

F-H code and beeping noise

error code which is serial communication error with motor contrl.
replaced M.Contl.brd but still have error.

Dec 03, 2007 | Kenmore Elite 45986 Front Load Washer

Not finding what you are looking for?
Kenmore Oasis HE 27082 Top Load Washer Logo

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers


Level 3 Expert

662 Answers


Level 3 Expert

5331 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides