Clock does not keep or display time - Zojirushi NS-ZAC18 Neuro Fuzzy 10-Cup Rice Cooker

Atomic clock keeps losing outside temperature Google Search ..try this link not sure if it will help you with yours.

SETTING THE CLOCK AND DELAY BREW TIME
To Set the Clock:
1.
Plug the power cord into a standard electrical outlet. The clock
will flash on the control panel to indicate that the time has not
been set yet.
2.
Press and hold the HOUR and MINUTE buttons until you reach
the current time. The AM or PM indicator will light at the bottom
of the display (Figure 1).
The clock is now set!
NOTE:
Pressing any button before setting the clock will cause the
clock to start keeping time from 12:00 a.m. You must set the clock
if you want to use the Delay Brew feature.

Does it appear momentarily when you press the clock key? If so, then you probably have the "energy-saver" feature turned on. To turn it off (so it "wastes" energy by displaying the clock all the time), press and hold that key. When you first press the key, the clock time will display... (Keep holding that key!) Then in about 7 seconds, the display will go blank.... (Keep holding that key!) Then in about 3 more seconds, the display will come back on. Now you can let go of that key, and the clock time will continue to display.

If you need further help, reach me via phone at https://www.6ya.com/expert/ronald_e6b9572cebe3ad27

Hi

If you have lost the outside temperature on the clock display then do the following:-

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappears.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.

Also check the link bellow:-

http://www.ehow.com/how_4597931_set-atomic-clock.html

Please get back to us if you have further query else please accept the suggestion.

Thank you for contacting fixya.com

The eoc has gone bad. Clock control. You will need the manufacturers number also starts with a P when ordering this part. Hope this helps.

There are three buttons, let's call them 1, 2, and 3, from left to right.


Clock
Time setting

A. 12 AM, PM or 24.00 h
With the clock in the time readout mode, keep
button (2) depressed for 4 seconds -12 AM, PM
or 24.00 flashing. After pushing button (1), either
a 12-hour (AM + PM) or a 24-hour setting
program can be selected. If you only want to
change the display mode, push button (3). The
clock then returns to its normal timekeeping
function.

B. Hours
Push button (2) a second time - hour display
flashes. Set hour by pushing button (1). After
pushing button (3)*, the clock returns to the time
readout mode with new hour setting.

C. Minutes
Push button (2) once more - minute display
flashes. Set minute by pushing button (1). Upon
pushing button (3)*, the clock is started -
accurate to within 1 second.

Stop watch function
The stop watch can only be set in motion if the
clock is in its normal timekeeping mode and not
during setting operations.
A. Push button (3) - 00:00 display appears;
B. Push button (1) - stop watch is on;
C. Push button (1) a second time - watch stops.
(Additional times can be added by pushing button
(1) again - stop watch keeps running. Push button
(1) once more to stop timing.)
D. Push button (2) - 00:00 display appears;
E. Push button (3) - normal timekeeping mode.

If button (3) is pushed during operation A and
B, the setting procedure must be restarted
(push button (2)).

try holding down clock button.. when you 1st hold it down it will appear.. keep holding til it disappear.. then when it comes back on let go of button.. if clock button don't try another like + or - sign.. good luck.. mike

If your clock is not keeping the correct time and you have done everythinh right, the problem lays within the IC or M icroprocessor on the Printed Circuit Board which the lcd clock display is attatched too.

They say to hold the button for 14 seconds or til it beeps, for it to stay on.

Please check the following website for all the info and faq.

http://skyscan.info/content/index.php?option=com_content&task=view&id=35&Itemid=40

Also,

If you have lost the outside temperature on the clock display after replacing the transmitter battery then do the following:

1. Make sure you have good batteries installed in the remote transmitter
2. Remove the batteries from the main clock and keep them out until the clock display disappers.
3. Re-install the batteries in the clock.
4. Wait until the display returns and includes the outside temperature display as well.
5. Set the clock again for current time/date etc.
6. Bingo. You are in business.

FixerUpper