Question about Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+

1 Answer

Garage door hey dude.. did you figured out how to fix your garage door ... i have the exact same problem...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 143 Answers

Do you still need assistance with your unit?

Posted on Sep 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Starts with the remote but shuts off when a door is opened


Garage Door Opener Troubleshooting step by step - YouTube

? 3:41
https://www.youtube.com/watch?v=b8w2w5ZAc1I
Feb 5, 2014 - Uploaded by Andrew Hill
How to Fix A Garage Door Opener - the opener shown is the Craftsman 1/2 HP ... First start with the obvious and easy to check problems. ... opener button on the wall will open the garage door but not your remote or keypad, ...

Auto Start Engine Shuts Off When open door -



The Top 10 Reasons Your Garage Door Won't Work

customoverheaddoors.net/reasons-your-garage-door-wont-work/
Jun 5, 2014 - To help you troubleshoot your garage door issues, here are the top 10 ...Garage Door Closes Part Way, Then Opens Again ... Automatic Garage Door Opener Runs for a Few Seconds then Turns Off but Door Doesn't Move

Jan 05, 2016 | Garage Doors

1 Answer

How do I program the garage door opener receiver on the garage after programming the garage door openner on the vehicle?


after you do the programing for the car you have to go back to the opener and press your learn button once. Then go back to your car and press and HOLD the button you just programmed your should see your light bulb blink on your opener after about a second or two.

Jan 27, 2015 | Garage Doors

1 Answer

What does the purple button light flashing on 1/2 horsepower craftsman garage door opener


I think the adjustment mode is on.

For example, that's from Craftsman manual:

""
Setting the Force
The force setting button is located on the left panel of the motor unit. The force setting measures the amount of force required to open and close the door.
1. Locate the purple button on the left panel of the motor unit (Figure 1).
2. Push the purple button twice to enter the opener into Force Adjustment Mode (Figure 2). The LED (Indicator Light) will flash quickly.
3. Push the remote control or control console (Figure 3). The door will travel to the DOWN (close) position.

""

Actually, you should just read carefully your garage door opener unit's manual.

Craftsman Garage Door Opener Remote

Jun 21, 2014 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

My garage door opener seems to loose power in the middle of opening and closing the door. I think it's theresult of the vibration the motor causes when it engages. I figure there is a loose connection...


Make sure all the connections on the rear of the motor unit are tight. You can remove the logic board and check for loose connections on the printed circuit. While you are there take a look at the drive gear. It is a white nylon gear just in front of the motor and may be going bad.

May 19, 2010 | Sears Craftsman LiftMaster Chamberlain...

1 Answer

I INSTALLED A NEW SEARS GARAGE DOOR OPENER YESTERDAY EVERYTHING WORK FINE EXCEPT I HAVE NOT BEEN ABLE TO PROGRAM THE OUTSIDE TOUCH PAD. tHIS PAD OPENS THE GARAGE DOOR ON THE DETACHED GARAGE DOOR WHICH IS...


New door openers have a different radio frequency than the old models. This is most likely your problem and you will need to buy the keypad that is compatible with the new opener.

Sep 14, 2009 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

How to switch back to automatic after manually close the garage d


mikey-moore's advice helped me figure out what to do but it's not exactly what I had to do. Manually open the garage door all the way. Then hit the automatic button you normally would use to open and close your garage door. The bracket slides back and locks into place. Hit the automatic button again and the garage door should automatically close.

Jul 19, 2009 | Sears Craftsman LiftMaster Chamberlain...

Not finding what you are looking for?
Sears Craftsman LiftMaster Chamberlain Garage Door Opener Wireless Keypad Model 976LM Security+ Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Sears Garage Doors Experts

Al Clark

Level 2 Expert

290 Answers

Cindy Wells

Level 3 Expert

4754 Answers

Pieter Vleeshouwers

Level 3 Expert

1410 Answers

Are you a Sears Garage Door Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...