Question about Frigidaire FGQ332ES Gas Dryer

1 Answer

Wrong dryer The dryer I have is a LGQ642DSO not the FG model. Does the previous solution still apply?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 210 Answers

PROBABLY

Posted on Jul 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Belt replaced around drum, too loose! Parts store insists it is the correct size for GE dryer. Model # DBXR453GT3WW (1996) Can't figure out what is wrong?


Hello,

The part# i have for that model number for the belt is WE12M29 the previous part number for that was WE12M22 is either of those the part number for the belt ?? if yes it should be the correct one

one more thing that may help ya is view the diagram here of how it fits onto the idler pulley/motor pulley http://www.repairclinic.com/Dryer-Belt-Diagrams for your dryer it will be DIAGRAM L


GENE

Aug 29, 2011 | GE Dryers

1 Answer

The dryer turns on and spins but no heat is being applied. Just curious as what my be the problem and how to fix. Thanks.


Hi,

If you are having problems with your gas dryer not heating the most common problem is that the ignitor goes bad. Even though it glows sometimes it is still not working properly.


if you dryer is gas check out this gas no heat tip....


If you have an electric dryer, you can have many different things that can go wrong causing the dryer not to heat.


check out this electric no heat tip...


heatman101

Dec 29, 2010 | Whirlpool Dryers

1 Answer

My dryer is making noise, vibrating and smells like it is burning


Hi,
Here is a tip that I wrote about dryers and noises...

It will help you determine what is happening there...

Dryer Repair Squeaks, Grinding, Clicking and Knocking Noise


heatman101


fg

Jul 22, 2010 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

When I turn the cycle control knob it no longer makes a noise


Hi,

There can be many reasons why your dryer will not start or turn...

The most common causes are the belt breaking or jumping off, or the motor goingbad...

Here are a couple of tips that I wrote will help you to figure out why yourdryer will not run...

Dryer Repair - The Dryer is not Turning

Dryer Repair - The dryer will not start


heatman101

fg

May 30, 2010 | LG DLG7188 Gas Dryer

1 Answer

How to find the heating element on the Kenmore 80 series... Model 67832794... trying to replace myself but can't figure where the heating element is located


remove the back of dryer,unplug,look to the right and you will see the heater box,the lower half is the heating coil,remove the 2 wires and 2 screws and pull the heater off,also you need to check the heater box fuse located on the upper left side fg heater box-mike

Feb 19, 2010 | Kenmore 63942 Dryer

1 Answer

Dryer does not get warm enough to dry a load in one cycle model fg 447ghso


check your vent on the dryer. if your filter or the vent pipes air flow is obstructed the dryer will not dry properly.

Oct 23, 2009 | Dryers

1 Answer

What is the routing of a dryer belt? It's a Roper dryer model GL6050VLO


To install a new belt and re-install the pulley, follow these steps:

1. Loop the drive belt around the dryer drum with the groove side facing the drum. (Try to line the belt up with the wear marks already on the drum from the previous belt).

2. With the tensioner in your left hand, insert the clip end of the idler pulley into the grooves on the dryer bottom casing with the idler wheel pointing to your left. (The grooves are directly in front of the drive motor.)

3. While holding the tensioner in place, insert the belt UNDER the wheel with your right hand and pull it up and over the drive motor pulley.

If this does not explain it well enough, you can also verify by going to repairclinic.com. Click on the Repair Help link and look for the "Dryer Belt Diagrams" link under the Special Features section on the next page. Look for Whirlpool and refer to diagram H.

You can also refer to pcappliancerepair.com for some excellent exploded view diagrams of your dryer. Just type in your model number as "GL6050VL0" (the last digit is a zero, not the letter O), and go to the "Bulkhead" section.

NOTE: Roper is manufactured by Whirlpool, so these instructions will apply.

If you have questions, or require additional assistance please let me know. I hope you find this information helpful.

Oct 17, 2009 | Dryers

1 Answer

Dryer will not start


Forgot to check the thermal fuse. Now working after changing fuse.

Mar 21, 2009 | Kenmore Dryers

Not finding what you are looking for?
Frigidaire FGQ332ES Gas Dryer Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dryers Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Tim Whalen

Level 3 Expert

3069 Answers

Are you a Frigidaire Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...