Question about Xerox DocuColor 3535 Copier

2 Answers

Xerox 3535 error code

Mmachine goes into scanning mode, wont exit,. also error code004346.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Went to xerox site , look for 3535, type in error code, saw what the problem was.

Posted on Jul 17, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

004-361 eror cods

Posted on Apr 13, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2013 civic hf goes to security mode and wont start after driving car and shutting it off it will not start


The system is computer controlled and it can be scanned for the fault that is causing this to happen. Talk to your local Honda service department.

Jun 15, 2017 | Cars & Trucks

1 Answer

2006 hayabusa will turn over but wont start


if bike has a computer chip i it it may need resetting o a diagnostic mmachine

Apr 11, 2013 | 2006 Suzuki GSX 1300 R Hayabusa

1 Answer

Hello, my CANON MP500 gives error 5B00. Please help me!!!!!


Try this:

5b00 error


press MENU button, SCAN button, COPY button, SCAN button.
wait a minute.
it may be enter into special mode: service mode

(3) USE > to got to NVRAM ACCESS
(4) set ABS-M LEVEL to 0
(5) set ABS-P LEVEL to 0
(6) Press STOP to EXIT



If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response

Thanks, Joe

Jan 29, 2011 | Canon Office Equipment & Supplies

1 Answer

Error 5800


Here's the thing you can do.
1 press menu
2 PRESS scan copy scan to enter service mode
3 use > to go to NVRAM ACCESS
4 set ABS-M LEVEL TO 0
5 Set ABS P LEVEL TO 0
6 Set press STOP to EXIT

Hope it solves your problem thanks.

Jan 15, 2011 | Canon Computers & Internet

1 Answer

HOW TO SOLVE PROBLEM ERROR 5B00 IN CANON IP2770


You need to reset your printer.

(1) Press MENU
(2) Press SCAN COPY SCAN to enter service mode
(3) USE > to got to NVRAM ACCESS
(4) set ABS-M LEVEL to 0
(5) set ABS-P LEVEL to 0
(6) Press STOP to EXIT

Nov 26, 2010 | Canon Office Equipment & Supplies

1 Answer

Printer will not print


you should manually reset your PURGE COUNTER to ZERO so that your printer will work again. Follow these steps:

Unable to Clean error means purge counter is already full. Please refer below for the instructions on troubleshooting your machine.


1. To enter MAINTENANCE Mode: Press MENU, MONO START, 4X on ARROW UP. (within 2 seconds).
2. Using arrow up button look for the following:
a. 8 then press SET
b. 0 then press SET
3. Using MONO START, just press it until the word "PURGE XXXXX" comes out.
4. Using arrow up button look for the following:
a. 2 then press SET
b. 7 then press SET
a. 8 then press SET
b. 3 then press SET
This is to reset the purge counter. Then press stop/exit
5. Using arrow up button look for the following:
a. 0 then press SET
b. 1 then press SET (To reset unit)
a. 9 then press SET
b. 9 then press SET (To exit Maintenance mode)

In some brother models SET = OK

Nov 03, 2009 | Brother MFC 210C All-In-One InkJet Printer

3 Answers

My Canon Pixma MP130 keeps saying the ink waste absorber is almost full.


It's a shop repair since you have to take apart fully, and also use diagnostic mode to reset the error.

Jun 26, 2009 | Canon PIXMA MP130 All-In-One InkJet...

1 Answer

Canon PIXMA iP 1500 does not print


Hi,
1 press menu
2 PRESS scan copy scan to enter service mode
3 use > to go to NVRAM ACCESS
4 set ABS-M LEVEL TO 0
5 Set ABS P LEVEL TO 0
6 Set press STOP to EXIT
Thanks

Thiru

Jun 17, 2009 | Canon PIXMA iP1500 InkJet Photo Printer

1 Answer

My MFC 8860DN does not scan or copy but instead says please wait


Turn the machine off and hold menu while turning it on and keep holding it while the machine starts up. This should go into maint mode.

When it gets into maint mode you can try 99 to exit. This is like a soft reset. Hard reset is hitting 01 in maint mode and then 99 to exit.

Let me know if this is helpful.

Jan 09, 2009 | Brother MFC-8860DN Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

980 people viewed this question

Ask a Question

Usually answered in minutes!

Top Xerox Office Equipment & Supplies Experts

Michel

Level 2 Expert

97 Answers

Xeroxrep

Level 1 Expert

33 Answers

Philip Hughes

Level 2 Expert

75 Answers

Are you a Xerox Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...