Question about Cameras

1 Answer

I unhooked my AverMediaVision130 Document camera at the end of school and I didn't write down the instructions on how to hook it back up and it isn't covered in the User Manual. I have a computer, projector(mounted on the ceiling), document camera, splitter and conputer extension cables. I can get either the camera to project to the screen or come through on the computer monitor, but I can not get the camera to project to screen and leave the computer screen on on the computer. Do you have a diagram on how to hook all of this up? I got tired of plugging and uplugging and decided to get help. Darlene La Rue

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

From the document camera first, I hooked the VGA OUT to the wall box that is connected to the projector mounted in the ceiling then I connected the VGA IN to the DATA DISPLAY on the SPLITTER. The Computer monitor cable connected to the LOCAL MONITOR connection on the SPLITTER. The connection that comes out ot the SPLITTER I connected to the PCU. Okay, that is what worked. Maybe this will help some other poor soul with this many connections. Especially when the instructions does not allow for this possibility. The books never seem to have the ones given that I need. Oh, Well, the joys of instructions. Darlene

Posted on Jul 17, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Brand new pioneer 820 watt amp worked for about ten minutes, now the speaker output light flashes on and off

You didn,t have the sub wire up properly, End fried the output transisters in the amp. Or it was not set (Properly)

Nov 05, 2012 | Pioneer Car Audio & Video

1 Answer

My orion 2150sx is smoking when powered

No some one did not have the speakers hooked up properly ,End probably went under the OHM,Rateing for the amp, Or use the wrong OHM SUb on it, OR if they used a Dual voice coil sub,Didn,t have it wired up Properly.

Oct 30, 2012 | Car Audio & Video

1 Answer

I have a 2007 trailblazer. The rear speakers didn't work and some of the head unit lights didn't work. I replaced the headed unit and that didn't fix it. I then replaced both speakers and one...

Put new wireing in going to both back speakers, Factory wireing is verry thin end it breaks with age. Change it over to at least 16 guage speaker wire or 12 guage, Your system will sound a lot better.

Oct 26, 2012 | Cars & Trucks

1 Answer

New laptop screen doesn't work

verify your ribbon cable didn't come unhooked when you set the new screen in, also make sure the inverter is hooked up properly.

May 06, 2012 | HP Computers & Internet

1 Answer

Hi, my hp laptop does not detect the built in cyberlink camera. It says to turn it on but I'm not sure how to.

maybe the camera you have isn't working or you didn't install it properly.
try to install it again following the manual instructions.

Jul 02, 2011 | Computers & Internet

1 Answer

How does the Lil' Wedgie install onto the bike seat? Are there instructions or a photo?

Refer to this picture which shows an oblique view of an upside down seat bag (go figure):

Flip the bag over.

Hook the strap at the front of the bag (just out of sight in the pic) around your seatpost and secure it.

Unhook the strap which goes over the top of the picture and out of sight. Completely disengage the two ends from each other.

Look at the two supporting rails in this picture.

Run one side of the strap over each rail from the inboard side, looping them down along the sides of the bag.

Route the long end through the small loop at the bottom center, up toward the other side, through the plastic buckle and back down the side. Snug it tight to secure what's in the bag by pulling down on it and press it in to hook the Velcro.

Access to the contents is through the U-shaped zipper. The zipper along the entire bottom is for letting the bag expand for larger loads. I alway put my stuff in with it expanded and then, if possible I zip the expandable zipper shut to compress everything and make it still and silent while riding.

Mar 15, 2010 | Cycling

1 Answer

How do you remove the rear back seat to a 2002 chevy monte carlo

Most cars that do not have bolts are hook at the front end of the seat. You need push down really hard on the front end of the seat and pull the seat forward and up. This will unhook the latch. Good Luck

Oct 05, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

Can not get projector to display document writer and computer

I know how it feels to have these kind of problems with a classful of children getting fed up so any time you get other problems try here and I'll try to help.

Sep 10, 2009 | Electronics - Others

1 Answer

Moultrie mfh-i-40 white wire inside is unhooked on one end what does it hook too


Aug 20, 2009 | Moultrie GameSpy 4.0 Digital Camera Deluxe

Not finding what you are looking for?

Open Questions:

Cameras Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cameras Experts


Level 3 Expert

102366 Answers


Level 3 Expert

3287 Answers


Level 3 Expert

70374 Answers

Are you a Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides