Question about Danby 7,000 BTU Portable Air Conditioner - Euro Gray

2 Answers

P1 message on constantly. Have replaced water reservoir numerous times, pushed reset buttons numeroustimes and air conditioner will not operate. Only been used three times

Posted by on

  • Heggster84 Aug 07, 2008

    I have emptied the water container and the P1 message is still up. A/C cannot be operated.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Your hose is pinched, when it coils into the rez. There are no sensors or anything. So just make sure the hose has no bends when going into the rez. It will fix your problem.

Posted on May 26, 2010

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

U have to leave it plugged in for 45 min while it de ices

Posted on Jul 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1 message on screen, just dumped the bucket full of water. Machine has basically shut itself down


Unplug it after replacing the bucket. Then plug it back in again and let it reset before you try to power up. Also the float sensor may be stuck in the full/shut off position... Lemmee know!

Jul 18, 2011 | Heating & Cooling

1 Answer

Hyundai HYU-65AE constantly resets to P1 code. What does this mean


Error detail Abnormality ofroom temperaturethermistor (TH1).
Inspected unit Indoor.Replace the thermistor. Thanks.

Mar 09, 2011 | Heating & Cooling

1 Answer

What is the P2 code on an everstar mpk 10cr1


<b>Unit Displays P1</b><br /> P1 error indicates that:<br /> <ol type="A"> <li>The water tank on the side of the unit is full. <li>The water tank in not properly seated in the housing. <li>The switch at the back of the water tank housing is not engaged or is loose </li></ol> <br /> <i>Solution</i>:<br /> <ol type="A"> <li>Empty the water tank. <li>Make sure the water tank is properly secured in the housing <li>Remove the water tank for the housing and gently tilt the switch at the upper left hand corner of the housing towards you. This should allow the tab on the water tank cover to engage the switch. </li></ol> <br /> <b>Unit Displays P2</b><br /> P2 error indicates that the spill reservoir in the base of the unit is full.<br /> <i>Solution</i>:<br />Move the unit to a location that is suitable for draining water from the unit.<br />Remove the plug in the lower center of the back of the unit and allow the water to completely drain <br />(Remember to replace plug.)<br /> <hr color="#cccccc" size="1" /> <b>Unit Does Not Cool/The Green Light is not on. </b><br /> Is the unit in the Cooling mode?<br /> <i>Solution</i>:<br />Press the mode button until cooling mode is selected. <br />Lower the temperature setting on the unit to the minimum setting. <br />(The temperature setting of the unit has to be lower that that of the room)<br />Wait 3 to five minutes for the compressor to start running.

Jul 06, 2010 | Danby DPAC8020 Air Conditioner

2 Answers

My danby portable air conditioner won't turn on


New or used? Is is plugged in? Is there electric at the plug? Plug a light in there and make sure it works as a test. Next, check the water pan to make sure it is not full of water. There is a switch there that could be causing the problem.

Jul 06, 2010 | Danby 7,000 BTU Portable Air Conditioner -...

1 Answer

I have a flashing P1 and the unit will not turn on


P1 usually refers to evaporator pan full with water. If you drain it out it will work fine. If you need to reset it just unplug the power cord for two minutes.

Sep 26, 2009 | Danby DPAC8020 Air Conditioner

2 Answers

Need owners manual for Everstar Portable AC MPM1-10CR-BB6


Needed the manual to clarify a P1 error message. Figured how to fix the error P1 on my own. there are two drains on the unit, one is always open as an overflow drip, the other at bottom of unit has a plug. I opened the plug at the bottom of the unit, drained the water, and the P1 error code cleared.

Jun 25, 2009 | Danby DPAC8020 Air Conditioner

1 Answer

Everstar Air Conditioner


probably, the p1 signals that the water pan is either full or not sitting properly. There is a small lever that it pushes when the tray is pushed in. It is a switch that might have pushed out of its housing. Mine had and I had to dissasemble the unit to get the switch back in place, then it worked fine. Good luck. Dean

Aug 06, 2008 | Office Equipment & Supplies

2 Answers

Everstar MPM1-10CR-BB6


Press and hold the turbo button while plugging in the unit. The AC will cycle through a few tests and mine showed that it had excess water. I have long vinyl tubing so the unit could drain outside the window but it thought whenever it would start or stop there was excess water (thus stopping the flow). I drained the excess water out of the line and voila

Jul 08, 2008 | Danby DPAC8020 Air Conditioner

8 Answers

Everstar MPM1-10CR-BB6


The directions have the steps to take when a "P1" error is flashing.

1) Remove the plug (the upper black plug not the lower) and attach the included drain hose.
2) Put a bucket under the hose.
3) Press the TURBO button for MORE THAN THREE SECONDS. The WATER INDICATOR will begin flashing telling the user that the FORCED WATER DRAINAGE feature is activated. You will even hear a little whirring noise.
4) Wait until the WATER INDICATOR stops flashing and no more water is flowing out of the drainage tube.
5) After the water is finished flowing, make sure that you FASTEN the DRAIN PLUG. Of course, failure to do this will flood the area.
6) The unit should now work.

You can also move the unit somewhere that you can remove the plug and let the water flow freely (you do not need to have it plugged in for this method) and once the water is finished, replace the plug and fire it up. It should then work correctly. It's also mentioned that the water should be drained quite often to prevent corrosion. I do it every few months and of course when winter approaches.

I like this air conditioner and have had really nice luck with it. A little loud but who cares. That's why there are SUBTITLES on the television.

Hope this helped.

RoC

Jun 17, 2008 | Danby DPAC8020 Air Conditioner

Not finding what you are looking for?
Danby 7,000 BTU Portable Air Conditioner - Euro Gray Logo

Related Topics:

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Danby Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8205 Answers

Dennis Boxerman

Level 3 Expert

903 Answers

mintvl

Level 1 Expert

5 Answers

Are you a Danby Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...