Question about Celestion C6-S Speaker

Open Question

Subwoofer stops working after about 15 mins.

My Celestion C6 subwoofer stops working after about 15 minutes. It seems to work fine until it gives out. When it stops working the power indicator light turns from green to red. The woofer is from the late 90's and it is hooked up to a Denon AVC-3000 amp from the early 90's through a monster y RCA style subwoofer cable. The cable runs from the single preamp mono jack on the amp to the L and R input terminals on the woofer. It looks lie the fuse is still intact.

Posted by on

5 Suggested Answers

SOURCE: I have a celestion s80

Dont remember which cap it is , but its 47 uf 35v, on one corner of the board. You can use a slightly bigger value and slightly higher voltage if thats all you can find. Check the two caps next to the voltage regulators, these go as well problem sorted!!!!

Posted on Oct 03, 2010

dunnbiker
  • 8546 Answers

SOURCE: Connecting Celestion S1i Subwoofer to

Attach the audio out or headphone out of your laptop via a suitable adapter to the RCA Line In and whatever other amplified speakers you might have to the Line Out according to their needs.

Posted on Dec 22, 2010

dunnbiker
  • 8546 Answers

SOURCE: my celestion s20 subwoofer won't play if i hook it

Tell your source (receiver???) that it has a sub and set it up to feed LFE out of that RCA jack.

Prove your sub pre-out works. Or send something like FM on Tape Out to the sub and see how that works out.

How did you hook a speaker wire to this model of powered sub? What was on the other end of that speaker wire? It's not designed for speaker level input.

Posted on Jan 28, 2011

  • 1 Answer

SOURCE: I have a Celestion CSW Sub woofer. It powers on as

This speaker has a low frequency roll-off filter. Does your program source have low enough frequencies to pass through the filter? The effect of the subwoofer on most music is very subtle unless there is heavy bass in the source. You should try some songs that have a heavy under beat.

How are you driving the CSW -- by way of the line input or as a series connection to your full range speakers?

Posted on May 06, 2011

dunnbiker
  • 8546 Answers

SOURCE: no sound from Celestion F20

Since these can be bi-amped or bi-wired (and you don't indicate if that is the case) you need to make sure the jumpers are secure (see the last picture http://archiwumallegro.pl/celestion_f20-1062028198.html) or (if the jumpers are removed) that you have viable amplifier signals coming to each speaker within the cabinet.

Posted on May 30, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello Guys,Can you please help? can I replace the sub woofer on my sony home theatre system DAV-DZ231 with a Celestion sub woofer s10


Presumably, the Celestion subwoofer is self-powered in which case it would connect to an RCA subwoofer output on your Sony system if there is one.

Oct 30, 2014 | Speakers & Subwoofers

1 Answer

HTS14 subwoofer (Harmon Kardon)powers off after 10-15 minutes


Yeah, it sounds like it's over heating. Are you driving it way loud?

May 23, 2014 | Speakers & Subwoofers

1 Answer

How do I set up a Celestion S10 Subwoofer...


OK
Voltage is relevant to where you live in the world. America it's 110. Europe mostly 220.
What you're asking is a very deep and complicated question.
I'm attaching a link with some articles.
What I suggest is that you find an upper end audio store and ask a 20 audio head to set up your system for you. Subwoofer Setup and Calibration for Best Bass

Apr 12, 2014 | Celestion S10 Subwoofer

1 Answer

My celestion s20 subwoofer won't play if i hook it up to sub out on receiver.but will play if i run a regular speaker wire to it. I know sub out is working on receiver.


Tell your source (receiver???) that it has a sub and set it up to feed LFE out of that RCA jack.

Prove your sub pre-out works. Or send something like FM on Tape Out to the sub and see how that works out.

How did you hook a speaker wire to this model of powered sub? What was on the other end of that speaker wire? It's not designed for speaker level input.

Jan 28, 2011 | Celestion S20 Subwoofer

1 Answer

Auto/on switch


unplug it when your not in use,,,

May 12, 2009 | Celestion S10 Subwoofer

1 Answer

Subwoofer works - sound goes away after some time


POSSIBLY A BREAK IN THE SPEAKER SUPPLY LEADS TO THE ACTUAL BASE UNIT
WE HAD THIS AND IT WAS NOT THE SPEAKER BUT THE BOLT ON CONNECTION UNDER THE SPADE TERMINAL ON THE BACK OF THE BASS UNIT

Dec 16, 2008 | JBL EON 15-G2 Powered DJ Speaker With EQ...

1 Answer

Cirwin vega home sub


make sure that there are not any power cords near the leads from the amp to the sub.

Jan 11, 2008 | Celestion C6-S Speaker

Not finding what you are looking for?
Celestion C6-S Speaker Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Celestion Speakers & Subwoofers Experts

Josh Whitehead
Josh Whitehead

Level 3 Expert

1146 Answers

 Grubhead
Grubhead

Level 3 Expert

4590 Answers

Pieter Vleeshouwers

Level 3 Expert

1423 Answers

Are you a Celestion Speaker and Subwoofer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...