Question about Fargo Pro L ID Thermal Printer

2 Answers

Lam Error/Out The card printing process stops when it gets to the point of the Thermal over-laminate being applied. The printer beeps, the Error Message, " Lam Error/Out" appears and the ready light blinks continuously. A few times, I was able to manually back the card up by the roller, but nothing seems to work now. I also tinkered around with the card guides to no avail. I will acquire another roll of over-laminate today, because the roll I have in the machine now is rather small. I have a deadline today. I may have to present the recipient with cards that have no over-laminate today, and give him a new one after the problem has been resolved. Your expert advice concerning this problem, will be greatly appreciated. Thanking you in advance, Kevin

Posted by on

2 Answers

Heat lamp is not working properly...
reasons,,,
1.Electricity is not proper.
2. heat lam damge.replace heat lamp.

Posted on Jul 18, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I contacted fargosupport.com and a technician walked through the solution, free of charge.

Posted on Jul 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My fargo Pro L is not laminating and always says lam adjusting


Try Updating the firmware on the printer and the lamination module.

Go to HIDglobal.com. Under the support tab, click drivers & downloads. Populate the drop down menus with make and model.

The most recent software is shown here. Go to the section "Misc." and download Fargo Workbench. This utility enables you to update the printer by automatically pulling the most recent version off the Manufacturers website. Very Useful.

Oct 07, 2014 | Fargo Pro L ID Thermal Printer

2 Answers

How to solve e220 and e218


Both of those errors revolve around the laminator.
E220 is Lam2 Tag Error
E218 is Lam 2 Head Lift Error
I would recommend replacing the laminator.

Sep 19, 2013 | Office Equipment & Supplies

1 Answer

Card Jam Error 112 & 245


please calibrate the Lam Film sensor.error 245 is lam sync error please check Lam power/connections and restart the Printer.

Oct 02, 2012 | Fargo HDP5000-LC ID Card Printer...

1 Answer

Check lam material


Your lamination material is either not compatible/the correct size or is jammed

Apr 10, 2012 | Fargo DTC550 Thermal Card Printer

1 Answer

I have a zebra p520i and it will print a one sided card then go into mechanical error, I then can press the select button and it will travel the card past the laminator section and into the exit hopper and...


This sounds like the feed rollers need cleaning. You can use the correct cleaning cards (your dealer should be able to get them for you - but make sure you follow the instructions on the card carefully) or use IPA fluid.on a lint free cloth.

Jun 03, 2011 | Office Equipment & Supplies

1 Answer

The message center say to check lam power and reboot required. How do I reboot the lam


Power unit off. Take Power cord off the printer.
Remove Lamination unit at the connector.
Check it for obstructions.
re-install the Lam unit.
Power up the unit.

May 25, 2011 | Fargo HDP5000 Thermal Printer

1 Answer

Printer does not respond to print button for test


REmove and renstall the drivers. Do this through the Printer folder. Delete the printer, unplug it, reboot. If you have the software, use it. If you need the software, get it via download from the manufacturer. Follow the manufacturers instructions as they appear on the screen.

Feb 25, 2010 | Zebra P640i Thermal Printer

2 Answers

Fargo pro l lamination


I cant even get my cards to print the lamination on there. Can you please help me!.. Can you show me pics on how you installed the Lamination rolls. Also is there a special driver you installed or option you clicked beside the over laminate one. THANK YOU SO MUCH!

Dec 06, 2007 | Fargo Pro L ID Thermal Printer

1 Answer

The card stucks


this is an old post, but are you using ultra card III cards by fargo?

Oct 25, 2006 | Fargo Pro LX ID Thermal Card Printer

Not finding what you are looking for?
Fargo Pro L ID Thermal Printer Logo

279 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fargo Office Equipment & Supplies Experts

pkwc

Level 2 Expert

254 Answers

Cindy Wells

Level 3 Expert

4946 Answers

Computer Links

Level 3 Expert

2385 Answers

Are you a Fargo Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...